1.
"Upon proper alignment of mounting holes, the two bolts and washers should be installed."
安装孔对准后,应该把两个螺栓和垫圈安装上去。
2.
The Study of Examination Effect of the Drilling Technology to Standard Penetration Test;
钻孔工艺对标准贯入试验影响的研究
3.
Impact of mismatching aperture in satellite-ground laser communication on pointing information
孔径不匹配在星地光通信中对对准信息的影响
4.
Effect on the accuracy of Root ZX of different size of apical foramen
不同根尖孔直径对Root ZX测量准确性的影响
5.
Effect of the Size of Detector Collimating Aperture on ICT Reconstruction Image
探测器准直孔径对ICT图像重建质量影响的分析
6.
In this paper, four calibration methods for pressure leak are introduced, namely, the constant varying pressure, the constant varying volume, the dynamic comparison method with quantitative gas and the dynamic comparison method with a reference leak.
介绍了定容变压法、压变容法、量气体动态比较法、考漏孔动态比较法对正压漏孔进行校准方法。
7.
Range alignment and motion compensation are the key techniques of ISAR.
距离对准和运动补偿是逆合成孔径雷达成象的关键技术。
8.
Install the defogger relay by aligning the relay terminals with the cavities in the junction block and pushing the relay firmly into place.
对准接线盒中有孔的继电器端子，安装除雾继电器，并把继电器插牢。
9.
electronic boresight scanning
电子孔径瞄准器扫描
10.
On the Theoretical and Practical Standards in the Doctrine ofConfucius s Benevolence;
试论孔子仁学的理论标准与实践标准
11.
Bolts are ground and flange holes are calibrated for perfect centering of the two flanges in respect of each other.
螺栓经过打磨，法兰螺栓孔也经过校准，实现了2个法兰相互之间的完美对中。
12.
Fit hinge 5 into the opening in the machine bed, and fit the machine head to table rubber hinge 6 before placing the machine head on cushions 7 on the four corners.
把铰链5放到机台的孔上，对准台板橡胶支座6，把头部放到四角的机头胶垫7上。
13.
In the act of measuring spheroid assemblage clearance,the noise is reduced and accurate images edge is gotten.
在对前、后孔配准图像的测量中,能够降低噪声,并能比较精确的得到图像的边缘.
14.
The Influence of Confucius Ideas upon Managerial Ethics of Chinese and Japanese Enterprises;
从海尔和松下的行为准则透视孔子思想对中日企业管理伦理的影响
15.
Effect of Preparative Processes on the Quasi-Static Compressive Properties of Porous SiC Ceramic/Zr-Based Amorphous Composites
制备工艺对多孔SiC陶瓷/Zr基非晶合金复合材料准静态压缩性能的影响
16.
The act of aiming.
瞄准，对准瞄准的行为
17.
Influence of Pore Diameter Distribution on Porous Nickel's Pore Volume Fractal Dimention
孔径分布对多孔镍孔体积分形维数的影响
18.
Method of Collimation and Image Processing Using CCD Pickup Camera in Aperture Measurement
孔径测量中ccd瞄准方法与图像处理