1.
Mount the arms on the pivot shafts so that the distance from the lower edge of the wiper arm tip to the upper edge of the lower windshield moulding is:
将雨刷臂安装在枢轴上以便使从雨刷臂边缘尖端到挡风模组上端边缘的距离是：
2.
Tighten the cartridge mounting screws finger tight. DO NOT TIGHTEN THEM FULLY WHILE THE ARM IS MOUNTED ON THE TURNTABLE.
将唱头螺丝锁紧。在唱臂安装在唱盘之前不要锁紧。
3.
One-Time Tensioning Formation Technology of Single Steel Strand Wire of Anchor Cable of Steel Cantilever Installed Truss Arch Bridge
钢桁架拱桥悬臂安装扣索单股一次张拉施工技术
4.
Install the push rods, rocker arms, pivots and bridges in the order they were remove
按照拆卸顺序安装推杆、摇臂、枢轴和桥臂。
5.
Install pitman shaft and side cover in the housing.
在机座中安装转向摇臂轴和侧盖。
6.
The arm with self-locking device, easy for adjusted, more safety.
设有托臂自锁装置,调整方便,使用安全.
7.
Installation and Maintenance of Vertical Folding-Type Disconnector
垂直折臂式隔离开关的安装、运行维护
8.
"In the second type, the coil spring is located between the upper and lower control arms, and the lower control arm has two points of attachment to the car frame. "
二,螺旋弹簧安装在上、下控制臂之间,下控制臂有两处与车架相连。
9.
He extended the arm attached to one of the metal balls of the transmitting instrument into an elevated aerial and connected the second arm to earth.
他将连接传导装置的一个金属球上的臂改装成高架式的天线，让另外一只臂接地安装。
10.
In a magnetic disk unit, an arm on which magnetic heads are mounted.
磁盘机中一种用于安装磁头的臂状部件。
11.
High Altitude Displacement Installation of Whip-typed Tower Crane Used in CCTV Main Building
CCTV主楼大型动臂式塔式起重机高空移位安装
12.
Installation of Tower Crane Used in Cantilever of CCTV Main Building
CCTV主楼悬臂部位大型塔式起重机安装技术
13.
Design and Evaluation of Light Manipulator Mounted on Wheelchair
安装于电动轮椅上轻型作业臂的研制及评价
14.
These capacity charts show the figures when handling load off main boom head sheaves in a case of mounting fly jib on top of main boom.
这些功能表显示了在主悬臂顶端安装飞臂情况下将负载操作离开主悬臂头滑轮时的数据。
15.
slave bangle
臂镯(妇女装饰用)
16.
"There are three types of coil-spring front suspension. In one, the coil spring is located between the upper and lower control arms, and the lower control arm has one point of attachment to the car frame."
有三种螺旋弹簧前悬挂结构:一,螺旋弹簧安装在上、下控制臂之间,下控制臂的一端与车架相连;
17.
With a roll ball rocking arm and balance tray. It is a smart design and convenient to be installed quickly.
备有流滚珠式驻持摇臂及平衡托架，设计巧妙，安装简便，快捷。
18.
Sometimes the camshaft is fitted directly into the cylinder head and operates on the valves without rockers.
有时，凸轮轴直接安装在气缸盖上并且不用摇臂控制阀门工作。