1.
valve-tappet clearance adjuster
气门挺杆间隙调节器
2.
Valve Lash Adjuster
气门间隙调节器又称液压挺杆
3.
tappet oil gallery
(气门) 挺杆润滑油道
4.
Install the hydraulic valve tappets.
安装液压气门挺杆。
5.
Valve sticking. Gum or carbon deposits on the valve stem will cause valve sticking. Excessive valve-stem clearance speeds up valve deposits.
气门沾着:气门杆上的胶质或积炭是造成沾着的原因。气门杆间隙过大会加速气门的积炭。
6.
Valve Breakage. Any condition that causes the valve to overheat or to be subjected to heavy pounding (as from excessive tappet clearance or from detonation ) may cause valves to Break.
气门破裂:气门过热或遭受重载(气门杆间隙过大或爆裂)均可造成气门破裂。
7.
"adjusting valve tappet clearances (also called adjusting valve lash), grinding valves and valve seats."
气门维修包括调校气门间隙(也称气门余隙),研磨气门和气门座.
8.
The valve lifter, a round cylinder, rides on the cam.
气门挺杆为一圆筒体，坐落在凸轮上。
9.
"After the cam lobe moves out from under the valve lifter, the valve spring forces the valve up onto its seat again."
当凸轮凸角离开气门挺杆,气门弹簧使气门重新回到气门座上。
10.
The value-opening mechanism includes a valve lifter and a cam on a camshaft.
一套气门开启机构包括一个气门挺杆和一个在凸轮轴上的凸轮。
11.
Hydraulic Valve Lash Adjuster (HLA) and Valve Train with HLA
液压气门间隙调节器及有间隙调节器的气门机构的研究
12.
"With this arrangement, the camshaft is directly below the valve lifter, and no push rods or rocker arms are necessary. "
"在这种装置中,凸轮轴直接装在气门挺杆下,并且不必有推杆或摇臂。"
13.
Valve Tappet Adjustment For Three And Five--Cylinder Engines
三缸与五缸内燃机气门间隙调整方法
14.
The effects of five adjusting parameters of valve timing, admission valve clearance, emission valve clearance, rotational speed ,load rate are interacted.
配气相位、进气门间隙、排气门间隙、转速、负荷五个调整参数之间是相互影响的。
15.
Using Vibration Signal to Diagnose Abnormal State of Engine Valves Clearance;
基于振动分析的气门间隙异常故障诊断
16.
Experimental and Clinical Study about Effects of CagA～+ Helicobacter Pylori Strain on Cell Gap Junction of Gastric Epithelial Cells;
幽门螺杆菌CagA～+菌株对胃上皮细胞间隙连接影响的实验和临床研究
17.
Effect of Helicobacter pylori on Cell Gap Junction Ultrastructure of Gastric Epithelial Cells
幽门螺杆菌对胃上皮细胞间隙连接超微结构的影响(英文)
18.
Fill the tester cup with hydraulic valve tappet test oil until the tappet is completely submerge
为测试杯注入阀门挺杆测试油，直到挺杆完全浸入水中。