1.
"The gear sector, toothed roller, or stud meshes with the worm."
转向摇臂轴上装有扇形齿轮、带齿滚柱或指销,用以和蜗杆啮合。
2.
Research of the Gearing Characteristics between Plastic Worm Wheel and Steel Worm;
塑料蜗轮与钢制蜗杆的啮合性能研究
3.
A Study on Meshing Theory and Optimal Design of TI Worm Gearing;
TI蜗杆传动啮合理论研究及优化设计
4.
Strength Analysis of Globoidal Worm Gearing with Roller Teeth and Point Engagement;
滚动式点啮合环面蜗杆传动的强度分析
5.
Theoretical and Experimental Research on Loaded Meshing of Involute Cylinder Worm-drive;
渐开线圆柱蜗杆传动承载啮合理论与实验研究
6.
Meshing Theory and Application Study of Grinding Gear with the Toroidal Involute Interior Thread Worm Grind Wheel;
TI内螺纹蜗杆砂轮磨齿的啮合理论及应用研究
7.
Effects of Design Parameters on Meshing Performance of Single Enveloping TI Worm Gearing
设计参数对一包TI蜗杆传动啮合性能的影响
8.
Analysis of the Mesh Theory between Plastic Helical Gear and Steel Worm
塑料斜齿轮与钢制蜗杆的啮合理论分析
9.
Meshing Analysis on Worm Gearings Based on CAD Technique
基于CAD技术的环面蜗杆传动的啮合分析
10.
A gear sector is meshed with the worm gear; rotation of the worm gear causes the gear sector to rotate.
蜗杆齿带动齿扇转动,齿扇与蜗杆齿啮合,这使的与齿扇相连接的转向摇臂左右摆动。
11.
Study on Meshing Analysis and Meshing Control of Double-enveloping Hourglass Worm-gearing Affected by Misalignment Errors and Load-dependent Deformation
制造误差与承载变形耦合条件下平面二次包络环面蜗杆的啮合分析与啮合控制研究
12.
Meshing Analysis of Non-backlash Double Roller Enveloping Hourglass Worm Gearing
无侧隙双滚子包络环面蜗杆传动的啮合性能分析
13.
This paper makes a meshing analysis about the spiroid gearing. Using the method of equivalent worm gearing, the assembly condition of Archimedes spiroid gears has been obtained.
通过锥蜗杆传动副的啮合分析,用当量圆柱蜗杆副的分析方法,得出阿基米德锥蜗杆副的装配条件。
14.
Analyzing the finger conical second enveloping ring-surface worm transmission by the fitting theory, the general mathematical model is put forward Modifing( a a angle add( I formation can eliminate oringinal arranging dense contact wire gear surface.
通过对指状锥面二次包络环面蜗杆传动进行啮合理论分析，提出了标准传动的通用数学模型。
15.
Research of Peculiarity of Engagement of Spiral Meshing Pair of Single Screw Compressor;
单螺杆压缩机螺旋啮合副啮合特性研究
16.
Spiral Meshing Pairs Manufacturing and Meshing Precision of Single Screw Compressor
单螺杆压缩机螺旋啮合副制造与啮合精度分析
17.
Research on 3D Molding and Meshing Clearance of Conical Twin-Screw
锥双螺杆的三维建模与啮合间隙研究
18.
RESEARCH ON MACHINING PRINCIPLE OF MESHING PAIR OF SINGLE SCREW COMPRESSOR
单螺杆压缩机啮合副的加工原理研究