1.
According to the theory of bearing forces and deformations, this paper gives distribution laws of the shearing stresses in the side fille welds of overlap connection with comparative accuracy.
依据受力与变形理论,较为精确地给出了搭接接头侧面角焊缝中的剪应力分布规律。
2.
Study of Length Calculation of Three Side Welded Lap;
三面围焊搭接角焊缝长度计算的探讨
3.
The backing plate shall be welded with matching electrodes so that the weld on the clad side is flush with the backing plate surface.
底板用配套焊条焊接，使复层侧的焊缝与背衬板表面齐平。
4.
This paper introduces the design of the bench of the assembling and welding of the lateral assembly with focus on welding jig.
本文着重从焊接夹具方面对侧围总成装焊拼台的设计作介绍。
5.
Application and Properties of Slab Sizing Press Module with Surfacing Welding
表面堆焊制备侧压机模块的性能及应用
6.
Numerical simulations of curved surface sidewall compression scramjet inlets with varied sweep angle and sidewall compression angle
变后掠角+变侧压角曲面压缩的高超侧压式进气道数值仿真
7.
On the section of the anterior horn of lateral ventricles appearing for the first time, the extended lines of the bilateral anterior rami of lateral sulcus intersected on the superior aspect of the genu of corpus callosum by obtuse angle.
在侧脑室前角首次出现的断面上 ,双侧外侧沟前支的延长线呈钝角相交于胼胝体膝上方 ;
8.
Experiment on tensile and shear strength of front fillet welded joint post-high-temperatures
高温后正面角焊缝抗拉剪切强度的试验
9.
Side view of hexagonal head bolt with adjustable thread length.
螺纹长度可调整的六角头螺栓的侧面图。
10.
Side view of hexagonal nut. Selection box height represents thread diameter.
六角螺母的侧面图。选择框高度代表螺纹直径。
11.
Side view of hexagonal socket bolt with adjustable thread length.
螺纹长度可调整的六角插口螺栓的侧面图。
12.
Side view of hexagonal cap nut. Selection box height represents thread diameter.
六角螺帽的侧面图。选择框高度代表螺纹直径。
13.
an arch whose jambs are not at right angles with the face.
拱的侧板与拱的正面搭配角度不对的拱。
14.
a polyhedron having a polygonal base and triangular sides with a common vertex.
有一个多边形底面和有一个共同顶点的三角形侧面的多面体。
15.
Both single and double fillet welds shall be as follows unless otherwise shown on the drawing.
除非图上另外标明，所有单、双面贴角焊缝高度如下。
16.
Side view of hexagonal jam nut. Selection box height represents thread diameter.
六角锁紧螺母的侧面图。选择框高度代表螺纹直径。
17.
When the needle penetrated deep palmar arch,the maximal angle between the needle and distal dorsal palm was 28.3±4.5°.
针尖刺中掌深弓时,针体与掌背平面所成的远侧角最大为28.3±4.5°。
18.
Lifting Surface Theory and the Numerical Method of Wings with Small Angles of Sideslip at Subsonic and Supersonic Speeds
亚、超音速小侧滑角机翼升力面理论和数值计算方法