1.
hour counter operating lever hook
时计数器活动杆构压片
2.
A beam that connects the piston rod to the connecting rod of a reciprocating engine.
十字头连接活塞杆和往复式发动机连杆的横杆
3.
rod that moves or is moved by a piston.
驱动活塞或被活塞驱动的连杆。
4.
Strength Analysis of Master Connecting Rod for Stern Motor Radial Engine
某型星形活塞发动机主连杆强度分析
5.
An Analysis of the Improvement of Piston-Con Rod-Crank-Shaft of CG125 Engine
CG125发动机活塞连杆曲轴改进分析
6.
"After the piston-and-connecting-rod assemblies have been removed from the engine and the pistons and rods separated, the rings should be removed from the piston.."
先将活塞及连杆组件从发动机上拆下再把活塞与连杆分开之后,即可将活塞环从活塞上取下。
7.
Two-point Floating Pneumatic Clamping Device of Toggle-lever Force-amplifer Based on Fixed Cylinder with Double Piston
基于双活塞固定气缸的铰杆-杠杆增力双点浮动夹紧装置
8.
The piston-rods connect the pistons to the parts of the engine which they move.
活塞杆把活塞和引擎中被活塞驱动的部件连在一起。
9.
PULL SHIFT LEVER TO LEFT SEVERAL TIMES TO ACTUATE DOWNSHIFT SWITCH.
把换挡叉杆向左拉动三次激活降挡开关。
10.
The Study of the Hydro-Mechanism Composite Transmission Device Base on Rod-Less Piston Hydraulic Cylinder;
基于无杆活塞缸的液压—机械复合传动装置研究
11.
Study on Optimisium and Modeling Simulation of Swing-Rod Movable Gear;
摆杆活齿传动的优化设计及建模仿真研究
12.
The Conditions for Disyllabic Verbs Acting As Predicates in BEI Constructions Revisited
双音节光杆动词“被”字句成活条件再考察
13.
Analysis on Fracture of Connecting Rod Unit Assembly for Piston of Car Engine
汽车发动机活塞连杆总成断裂失效分析
14.
"The connecting rod carries the power thrusts from the piston to the crankpin. At the same time, the rod is in eccentric motion."
"连杆的作用是将活塞承受的压力传给连杆轴颈。同时,连杆做偏心运动。"
15.
As the piston descended, a ratchet engaged the piston rod and engine shaft and thus power was transmitted.
当活塞下行时，棘轮连接活塞杆和发动机轴，因此将功率输送出去。
16.
Bang! There is an explosion in the cylinder. The explosion pushes the piston down. The piston is attached to a rod. The rod is attached to the crankshaft of the car.
砰!汽缸内产生爆炸，把活塞向下推动，活塞连着连杆，连杆又连着汽车曲轴。
17.
"As the piston nears TDC, ignition takes place. The high combustion pressures drive the piston down, and the thrust through the connecting rod turns the crankshaft."
当活塞接近上止点时,发动机点火。燃烧产生的高压驱动活塞向下运动,通过连杆,推动曲轴转动。
18.
metal block that connects to a piston; it slides on parallel guides and moves a connecting rod back and forth.
一个与活塞相连的金属块；它在平行导杆上滑动，并且引导机器上的连杆儿来回移动。