1.
YS Automatic Girth Welder (YS-AGW-I/II) is mainly used in horizontal girth inside / outside welding of large tanks、vessel etc. The welder applies submerged arc welding.
型埋弧自动横焊机采用埋弧横向焊接工艺，主要用于大型储罐、容器等内外环缝的焊接.
2.
Study of Dynamic Fracture Toughness and Structure of 10Ni5CrMoV Steel MIG Horizontal Position Welding Joint;
10Ni5CrMoV钢MIG横焊焊接接头的动态断裂韧性及组织研究
3.
Study on Transverse Welding Process with Pulsed Submerged Arc Welding Technology and Its Application in Oil Tank Manufacturing;
脉冲埋弧横焊工艺研究及其在石油储罐焊接制造中的应用
4.
The Choice of Welding Process Variable of Thick Board Automatic Horizontal Welding Based on ANSYS Numerical Analysis
基于ANSYS数值分析的中厚板自动横焊焊接工艺参数的选取
5.
transverse submerged arc welding
横列双丝并联埋弧焊
6.
series submerged arc welding (SAW-S)
横列双丝串联埋弧焊
7.
horizontal rolled position
转动横向焊位置(指管子环形接头横向焊
8.
horizontal fixed position
固定横向焊位置(指管子环形接头横向焊
9.
The Study of the Horizontal Residual Stresses of the Butt Welded Joint of Steel Member;
钢构件对接焊焊缝横向残余应力研究
10.
Study on Fatigue Behavior of Transverse Joints of AZ31B Magnesium Alloys with TIG-Welding;
AZ31B镁合金TIG焊横向接头疲劳性能研究
11.
Judge of Transverse Crack of Thick-Walled Seam by Ultrasonic Testing Method
厚壁焊缝横向裂纹的超声波判别方法
12.
What welding methods do you use in connecting the plates, frames, and beams?
在焊接钢板,肋骨，甲板横梁时，你们用什么焊接方法？
13.
Transverse/cross/lateral contraction deformation：The component contracts in the upright direction of weld after weiding.
横向收缩变形：构件焊后在垂直焊缝方向上发生的收缩。
14.
The point of penetration through the diaphragms is sealed by E-beam welding.
通过横膈膜的穿透点用电子束焊接来密封。
15.
Mechanical Properties of Iron Based Surfacing Alloys Applied DC Transverse Magnetic Field;
直流横向磁场作用下铁基堆焊合金的力学性能
16.
Research on Technology of Rotating Arc Horizontal Narrow Gap Welding of 12Ni3CrMoV Steel
12Ni3CrMoV钢旋转电弧窄间隙MAG横向焊接工艺研究
17.
Effect of Transverse Magnetic Field Frequency on Microstructure and Properties of Fe5 Deposited Metal
横向磁场频率对Fe5堆焊合金组织性能的影响
18.
There are two methods for welding radial stiffeners to bias-rail box girder: welded all around and open at tensile flange.
起重机偏轨箱形梁横向加强板有加强板四周均焊和在受拉翼缘处空开2种焊接方式。