1.
Remove the all of urethane from all pinchweld flanges.
由夹紧焊接凸缘去除所有尿烷。
2.
Inspect and repair the windshield opening and pinchweld flanges.
检查并修理挡风玻璃开口与夹紧焊接凸缘。
3.
Install and inspect the fit of the windshield on the pinchweld flanges as follows:
安装并检查夹紧焊接凸缘上挡风玻璃的配件如下：
4.
Chimes shall be mechanically seamed or welded.
桶的凸边必须用机械方法接合，或焊接。
5.
Indicates concave, convex or flush welds. Increase height to fit above other weld symbol.
指示凹焊缝、凸焊缝或平焊。增加高度以配合其他焊接符号。
6.
a hinge mortised flush into the edge of the door and jamb.
直接被焊接到门和柱的边缘的铰链。
7.
For instance, you should make sure that the insulations between the soldering tweezers and welding cable are ok and the earthing point and each termipoint of soldering machine are in good condition.
如焊钳和焊接电缆的绝缘是否有损坏的地方，焊机的外壳接地和焊机的各接线点接触是否良好。
8.
These include gusset plates welded to the flange.
这些包括焊接到翼缘上的节点板。
9.
Microstructure and Properties of Loop Projection Welding Joint Between Large-Diameter Screw Nut and Electrogalvanizing Thin Steel Plate
厚大螺母与镀锌薄钢板环凸焊接头组织与性能
10.
Drag onto the page to add concave, convex, or flush welds. Increase height to fit above other weld shapes.
拖到绘图页后，可以添加凹焊缝、凸焊缝或平焊。增加高度以配合其他焊接形状。
11.
"When joint is filled, a continuous rim of brazing alloy will be visible."
连接处被充满后,就会看到焊接合金的边缘。
12.
Finite Element Simulation of Welding Residual Stress for the Integrate Insulation Adapter
整体绝缘接头焊接残余应力有限元模拟
13.
Load-deformation Analysis of a flanged Connection System Subjected to External Loads
外载荷作用下凸缘联接系统的受力与变形分析
14.
Analysis and countermeasures of overproof of the edge deviation of welding line in circular seam welding of boiler drum
锅筒环缝对接焊缝边缘偏差超标分析及对策
15.
Insulation Structure for a High Current Diode by Ceramic-metal Welding
基于陶瓷-金属焊接的强流二极管绝缘结构设计
16.
The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection.
第二种是产生于立柱翼缘与主梁翼缘连接处的坡口焊缝焊趾处的裂纹。
17.
Butt welded 1;Butt welded 2;Butt welded 3;Butt welded 4
对接焊接 1;对接焊接 2;对接焊接 3;对接焊接 4
18.
Radial ball bearings with flanged outer ring--Flange dimensions
GB/T7217-1987凸缘外圈向心球轴承凸缘尺寸