1.
FEM Analysis Software Is Used to Calculate the Strength of Scoop Type Hoisting Machine
有限元分析软件在轴承强度计算中的应用
2.
Optimization Design of Bearing for Internal Combustion Engine Considering Crankshaft Strength;
计及曲轴强度的内燃机轴承优化设计
3.
Analytical Investigation on Strength and Main Bearing Lubrication of CA4D32 Diesel Engine Crankshaft System Based on a Simulation Technique;
柴油机曲轴轴系强度和主轴承润滑仿真研究
4.
Coupling Research on Tribology, Stiffness and Strength of Crankshaft-bearing System;
曲轴—轴承系统摩擦学、刚度和强度的耦合研究
5.
RUGGEDNESS. Automotive ring gear differential. Axle shafts on roller bearings.
强度：自动差速齿轮，滚子轴承上的刚性车轴。
6.
3D Finite Element Analysis of Stiffness and strength of Main Bearing Cap of Internal combustion Engine
内燃机主轴承盖强度和刚度的三维有限元分析
7.
Coupling Researches on Dynamics Tribology Stiffness and Strength in the Crankshaft-Bearing System of Internal Combustion Engine;
内燃机曲轴—轴承系统动力学摩擦学刚度和强度耦合研究
8.
Analysis of Static Strength and Stiffness for Spindle in High Speed Rotating Hydrostatic Bearing Union
高速旋转静压轴承接头芯轴的静强度和刚度分析
9.
Steel and Copper-Lead Alloy Bimetallic Cast Bearings:A Study of Adhesive Strength
铸造钢—铜铅合金双金属轴承粘结强度的研究
10.
Direct strength method for calculation of the bearing capacity of thin-wall aluminum alloy members under axial load
薄壁铝合金轴压构件承载力计算的直接强度法
11.
Analysis of rock-socketed pile uniaxial compressive strength and bearing capacity of pile tip at three dimensional effects
嵌岩桩单轴抗压强度和三维作用下桩端承载力
12.
Plain bearings-Metallic multilayer plain bearings-Destructive testing of bond for bearing metals
GB/T12948-1991滑动轴承双金属结合强度破坏性试验方法
13.
Bonding Mechanism and Strength of Al-Pb Alloy Strips and Hot Dip Aluminized Steel Sheets by Hot Rolling
铝铅轴承合金与热浸铝钢板的热轧复合机制与结合强度
14.
EFFECT OF Si ON THE INTERFACIAL BONDING STRENGTH OF Al- Pb ALL OY STRIPSAND HOT DIP AL UMINIZED STEEL SHEETSBY HOT ROL LING
硅对铝铅轴承合金带与热浸铝钢板热轧复合界面强度的影响
15.
Excessive friction in strut upper bearing
支柱上轴承磨损过度
16.
Babbits are known as the superior bearing metal in anti-friction property,butsince their lower fatigue strength,bearing of these metals are apt to crack and spalling,whenthey serve in high load condition.
巴氏合金是减摩性最好的轴承材料,但是其疲劳强度低,在高载荷下轴瓦合金层容易开裂剥落。
17.
CAI bearings are of motor class bearings and the common tolerance is shown on the attached data sheet.
CAI轴承一般为电机级轴承，最常用的轴承公差精度见附表所示。
18.
All bearings are rolling bearings and the shafts are made of alloy steel.
轴支承全部采用滚子轴承。轴材料均为合金钢。链条均为强制润滑。