1.
Effect of Welding Process on Microstructure and Properties of Surfacing Layer with D212 Welding Electrode
D212焊条堆焊工艺对堆焊层组织性能的影响
2.
Research on Corrosion Resistance of Overlaying Welding Layer Using A102,A132 and A302 Stainless Steel Electrode
A102、A132和A302焊条堆焊层耐蚀性研究
3.
The technology requirements and characteristics of overlay of a refractory steel build-up welding wire are introduced.
介绍了一种热强钢堆焊焊条的堆焊工艺要求、焊层特性。
4.
Study on Strip Surfacing Technologies and Mechanical and Property of Surfacing Deposit for 2.25Cr1Mo Steel;
2.25CrlMo钢带极堆焊工艺及堆焊层组织、性能研究
5.
Study on the Overlaying Property and Hot Corrosion Resistance of Fe_3Al Alloy Overlayer;
Fe_3Al合金堆焊及堆焊层的耐热腐蚀性能研究
6.
The Influence of Carbon Content on the Hardness and Microstructure of Layer on Weld Deposit Rob with Multi-elements Alloying System
碳含量对多元合金系堆焊焊条堆焊层硬度的影响
7.
By means of multi layer and multi pass lap surfacing, the surfacing layer with big thickness and area can be acquired.
采用多层焊和多道搭接工艺可获得大厚度、大面积堆焊层。
8.
The loss of C,B,Si,Cr and other elements in coatings decreases in the order of plasma,autogenous and faradic spraying.
焊层中的C、B、si、Cr等元素烧损率以等离子堆焊最大,火焰喷焊重熔次之,感应熔焊最小;
9.
Cracking Analysis of Arc Hardfacing Layer of Bainite Steel Frog
贝氏体钢辙叉电弧堆焊层的开裂分析
10.
Study of the Reliability of Power Device with Lead-free Heat-sink Attachment;
功率器件无铅焊料焊接层可靠性研究
11.
Study on the Surface Coating of Welding Wire of CO_2-Gas Shielding Arc-Welding;
CO_2气体保护焊焊丝表面涂层技术探索
12.
| wandering block sequence
电弧飘移多层焊次序
13.
Effect of Cu and Nb on Microstructure and Tensile Strength of Multi-Layer Weld HASL Steel;
铜和铌对HSLA钢多层焊焊缝组织和性能的影响
14.
Effects of the Size Parameters of Flip-chip Device on Low-K Layer and Solder Joints Reliability
倒装焊器件尺寸参数对低k层及焊点的影响
15.
Preparation and welding performance of amorphous interlayer alloys for TLP bonding
TLP焊用非晶态中间层合金的制备及焊接性能
16.
Research on Microstructure and Property of Flux-cored Welding Wire Wear-resistant Overlay
药芯焊丝堆焊耐磨覆层组织性能试验研究
17.
Laser-based visual recognition of multi-pass seam in robot arc welding
机器人多层多道焊缝激光视觉焊道的识别
18.
The backing plate shall be welded with matching electrodes so that the weld on the clad side is flush with the backing plate surface.
底板用配套焊条焊接，使复层侧的焊缝与背衬板表面齐平。