1.
Temperature Imbalances in Convection Superheater and Reheater Panels of Utility Boilers
电站锅炉对流过热器和再热器的同片热偏差
2.
Experimental and Numerical Investigation on the Heat Difference Control Using Jet Flow Method;
射流整流法控制热偏差的理论分析与试验研究
3.
The difference of heated area between tubes is very small, so the thermal deviation mainly results from inhomogeneous endotherm and flux.
但由于管子毛间的受热面积差异很小，过热器的热偏差主要由于吸热不均匀和流量不均匀造成。
4.
Research of Heat Deviation Evaluation System for Super-Heater and Reheater Based on Web Virtual Instrument;
基于Web虚拟仪器的过、再热器热偏差评估系统的研究
5.
Calculation Method of Heat Deviation And Special Study To Wall temperature For Super-Heater System of Large Capacity Boiler;
大型电站锅炉过热器系统热偏差计算与壁温特性研究
6.
Application of Counter-tangential Auxiliary Air on Reheater Retrofit of a 1175 t/h Boiler Against Heat Deviation
辅助风反切方式在1175t/h锅炉再热器热偏差改造中的应用
7.
Investigation on the Effect of the Ratio of Staged Air in the Total Air on HeatTransfer Difference on High-Temperature Heating Surfaces of a 600MW Supercritical Boiler
600MW超临界锅炉炉内分级送风比例对高温受热面热偏差影响的研究
8.
Thermocouples age with time and readings drift.
热电偶随时间而老化，读数会偏差。
9.
" Hot-rolled beam steel-Dimensions, shape, weight and tolerances"
GB/T706-1988热轧工字钢尺寸、外形、重量及允许偏差
10.
" Hot-rolled channel steel-Dimensions, shape, weight and tolerances"
GB/T707-1988热轧槽钢尺寸、外形、重量及允许偏差
11.
" Hot-rolled equal--leg angle steel--Dimensions, shape, weight and tolerances"
GB/T9787-1988热轧等边角钢尺寸、外形、重量及允许偏差
12.
" Dimensions, shape, weight and tolerances for hot-rolled flats"
GB/T704-1988热轧扁钢尺寸、外形、重量及允许偏差
13.
Dimenisions shape weight and tolerances for hot-rolled wire rods
GB/T14981-1994热轧盘条尺寸、外形、重量及允许偏差
14.
" Dimensions, shape, weight and tolerances for hot-rolled L-sectional steel"
GB/T9946-1988热轧L型钢尺寸、外形、重量及允许偏差
15.
Measuring method for power deviation rate of infrared heater
GB/T7287.8-1987红外辐射加热器功率偏差检测方法
16.
Deviation Analysis and Amendant on PID Temperature-controlling System of Thermal Processing;
热处理炉PID控温系统的偏差分析与修正
17.
PRODUCTION PRACTICE OF ENHANCING EQUILIBRIUM RATIO OF THE MINUS-DEVIATION ROLLING IN THE HOT ROLLED ANGLE
提高热轧角钢负偏差轧制均衡率的生产实践
18.
INFLUENCE OF BLADE-STAGGER DEPARTURE ON THE MIGRATION OF HOT STREAK IN TURBINE PASSAGE
叶片安装角偏差对涡轮通道内热斑迁移的影响