1.
No spalled paint exists at the plug weld and for a short distance each side of the plug welds.
在塞焊焊缝处及塞焊周围距离内无细漆碎屑存在。
2.
Close examination of the plug welds showed the existence of herringbone patterns near the slag and voids in welds.
对塞焊焊缝的详细检查表明在焊渣及气孔附近，焊缝中存在着人字型裂纹。
3.
The spcimens were machined such that plug weld was centered on the width of the specimen.
对试件进行了机加工以使塞焊焊缝位于试件宽度中间。
4.
Thus the fracture likely initiated from fatigue sharpened cracks originating from slag and void in the plug welds.
因此，断裂可能是由于从塞焊焊缝内的焊渣和气孔外形成的尖锐的疲劳裂纹而产生的。
5.
Welding the welds which are stagger first, then is the straight ang long weld.
先焊错开的端焊缝，后焊直通长焊缝。
6.
Welding to Fillet Weld Crackle of Superheater Connecting Screw Plug for 1 025 t/h Boiler
1025 t/h锅炉过热器连接管螺塞角焊缝裂纹的焊接
7.
DC seam welder-"C"France Type.
直流缝焊机,"C"型。
8.
Ceramic Cushion of Steel Pipe Weld Aided Device and Its Welding Procedure
钢管焊缝陶瓷垫补焊装置及焊接工艺
9.
Visual Sensing for Automatic Weld Tracking Systemto CO_2 Pre-welding of Longitudinal Welded Pipe
直缝焊管CO_2预焊视觉传感焊缝自动跟踪系统
10.
Research on pipeline girth welding joint with copper infiltration and copper back-up shoes root welding
管道环焊缝采用铜衬垫根焊及焊缝渗铜研究
11.
Longitudinal Submerged Arc Welded Pipe Weld Tracking Method and Misalignment Analysis
直缝埋弧焊管焊缝跟踪方法与焊偏分析
12.
The Modification to Inside Weld Grinding Machine for JCOE Formed Longitudinal Submerged Arc Welded Pipe
JCOE直缝埋弧焊管内焊缝磨削机的改造
13.
Indicates concave, convex or flush welds. Increase height to fit above other weld symbol.
指示凹焊缝、凸焊缝或平焊。增加高度以配合其他焊接符号。
14.
Amendment to the Weld Reinforcement Measurement of SAW Pipe with General Welding Measurement Ruler
通用焊接检验尺测量埋弧焊管焊缝余高的修正
15.
Analysis on key technologies for pipeline internal circumferential automatic welding machine with multi-torch
管道环焊缝多焊炬自动内焊机关键技术分析
16.
Research of root welding technology and welding procedure with back-up shoes pipeline girth welding
带衬垫的管道环焊缝根焊技术及焊接工艺
17.
Research on Welding Seam Formation Characteristics of Manual Arc Welding and CO_2 Gas Protection Welding
手工电弧焊与CO_2气体保护焊焊缝成形特征研究
18.
This welding line should be gouged and welded again before tightness inspection.
这条焊缝在密性检查前要碳刨、焊。