1.
Indicates a weld in a flared-bevel groove. Stems will elongate when height is increased.
指示在喇叭形坡口焊接。杆可随着高度的增加而拉长。
2.
Cracks have been found in the flange and web splices at groove welds in at least four bridges.
至少在四座桥梁的翼缘板和腹板拼接坡口焊缝中发现了裂纹。
3.
Often lack of fusion adjacent to the girder web in the transverse groove welds led to the cracking.
在靠近主梁腹板的横向坡口焊缝处常常出现未熔透而导致裂纹。
4.
The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection.
第二种是产生于立柱翼缘与主梁翼缘连接处的坡口焊缝焊趾处的裂纹。
5.
These attachments were considered secondary components, so no weld quality control has been imposed on the groove weld splice.
这些附连件被看作是次要的部件，所以在这种坡口焊接中没有进行焊接质量控制。
6.
The old method of soldering metal sheets together has now been largely replaced by welted joints, which are made by a special efficient mechanical device.
搭接贴角焊接金属薄板的老方法,现今已基本上为对接坡口焊所取代。
7.
A large number of these cracks occurred because the groove welded component was considered a secondary member or attachment.
发生这许多裂纹是因为把这些坡口焊接部件作为次要构件或附件考虑。
8.
Study on Groove Shape and the Open Angle of End Tab of UOE Pipe;
UOE焊管坡口形状与引弧板开口角研究
9.
Effect of Outside Welding Groove Angle on Weld Quality of X80 Grade SSAW Pipe
外焊坡口角度对X80级螺旋埋弧焊管焊缝质量的影响
10.
Add metal from the rod by dipping the end into the pool so that it melts and makes up the vee.
将焊条一端浸入池内熔化，填满V形坡口。
11.
A study of the improvement of the butt weld groove of a boiler set box and pipe
锅炉集箱和管道对接焊坡口的改进研究
12.
Visual detection of welding groove gap with linear laser source
采用激光线光源的焊接坡口间隙视觉检测
13.
Research on Welding Gradient Optimization Process of 80kg Heavy Gauge Steel Plate in Hydraulic Support
液压支架用80kg级高强钢焊接坡口角度优化研究
14.
Research on real-time processing images of non-groove butt weld based on structured light
基于结构光无坡口对接焊缝图像实时处理研究
15.
Investigation on the T_(8/5) of Multi-pass Compound Groove Welding for X80 Pipeline Steel
X80管线钢复合型坡口多道焊的T_(8/5)研究
16.
One side welding thermal cycle measuring experiment of heavy plate with V-shape groove
特厚钢板V型坡口单面焊接热循环测定实验
17.
Calculation of layered welding material dosage based on model of variant parameter groove
基于变参数坡口模型分层焊材消耗计算
18.
For all processes, the Welding Procedure Specification (WPS) shall contain a detailed cleaning procedure indicating joint preparation prior to welding.
对于所有焊接方法，焊接工艺规程都应详细包含清除方法，说明焊前坡口的准备。