1.
tap(ping) drill
螺丝孔钻，螺丝底孔钻
2.
Insert and screw the mounting screws through the motherboard screw holes and into the standoffs.
再将螺丝分别锁定在固定主机板用的铜柱螺丝孔位置中。
3.
Only one wrench is able to install and dismount, due to fixed screw holes.
有固定螺丝孔，装卸只要一支扳手，更方便。
4.
Factorial Analysis on Microleakage at the Fixed Screw Holes of Implant Denture;
种植义齿固定螺丝孔封闭后微渗漏之析因分析
5.
"Screw the standoffs that came with your case into the appropriate screw holes on the case, or if your case has a mounting tray, remove it and screw in the standoffs."
将随电脑机壳出货的铜柱锁在机壳欲安置主机板的螺丝孔中。
6.
Mount restrictor bar into the restrictor bar groove of upper die, mount adjusting bolt for restrictor bar into the bolt hole in the restrictor bar, then mount lower press block, upper press block.
在上模节流棒槽内装入节流棒，将节流棒调节螺栓装配进节流棒的螺丝孔中，再装配上压块。
7.
balance wheel oil cover screw
平衡轮注油孔盖螺丝
8.
Remove screws at wheel opening.
拆卸车轮孔处的螺丝。
9.
a threaded screw for machine parts; screws into a tapped hole.
一种适用于机器部件的螺纹螺丝；可以放进塞孔的螺丝。
10.
The wire thread insert used in screw hole of the blade
关于钢丝螺套在削片机刀片螺孔中的应用
11.
a screw with a hexagonal hole in the head.
针头有六角形的孔的螺丝。
12.
an awl for making small holes for brads or small screws.
给曲头钉或小螺丝打孔的一种锥子。
13.
a threaded fastener used either with a nut or with a tapped hole; slotted head can be driven by a screwdriver.
一种或有螺帽或有塞孔的螺纹扣件；其开槽头可以由螺丝起子钉入。
14.
Tapping is the process of cutting a thread inside a hole so that a cap screw or Bolt may be threaded into it.
攻丝是在一个孔中车出螺纹,以便装上有帽螺钉或螺栓。
15.
"Drill & tap for M16X2-1.38 Deep NPT,16 places for cover plate mounting screw"
钻孔,攻出一只M16X2-1.38深NPT螺纹,16处,该螺纹应与盖板固定螺丝配套
16.
"Bolts,screws & nuts"
"螺栓,螺丝及螺帽"
17.
This eyelet is so small that even the smallest screw cannot pass through.
这个孔眼太小了, 最小的螺丝钉都穿不过去。
18.
Installing bolts allowed to use gas cutting bore hole and never more than two gaskets pad not sexual bolts, exposed screw bolt length of not less than2-3 deduction.
安装螺栓孔不允许用气割扩孔,永乆性螺栓不得垫两个以上垫圈,螺栓外露丝扣长度不少于2～扣.