1.
Lock rings at the end of shaft with bolt
GB/T892-1986螺栓紧固轴端挡圈
2.
Lock rings at the end of shaft with scre
GB/T891-1986螺钉紧固轴端挡圈
3.
Remove vibration damper bolt and washer from end of crankshaft.
从曲轴端拆下减震器螺栓和垫圈。
4.
A wide range of standard stampings, non-standard products, stainless steel washers, internal/ external teeth washers, rings, circlips for holes, circlips for shaft, other fasteners, fittings, seal washers and clamps主要生产各种标准件冲压件.各种非标产品.
不绣钢垫圈;内外齿垫圈;挡圈;孔用挡圈;轴用挡圈;纱嘴头,其他紧固件、接件密封垫圈卡圈.
5.
Experimental Study on Fastening Bolt Axial Force of WSGG Anchor Basted on CFRP Sheet
CFRP波形齿锚具紧固螺栓轴力的试验
6.
Lock ring with scre
GB/T884-1986螺钉锁紧挡圈
7.
Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.
在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。
8.
A Study on the Design Method of the Clamping Bolts on the Cable End of Motor Vehicle Winch
汽车绞盘钢丝绳端紧固螺栓设计方法的探讨
9.
square collar-head set-bolt
方头凸缘端紧定螺栓
10.
Lock rings with screw and circlip
GB/T885-1986带锁圈的螺钉锁紧挡圈
11.
Install the bolts attaching the end cap to the front fender.
安装连接末端端盖到前挡泥板的螺栓。
12.
Secure the controller to the floor/base plate with bolts and washers and tighten.
用螺栓和垫圈,将控制装置安全地紧固在地面/底板上。
13.
The flange gasket bolts for the gate valves should be retightened during installation as the bolts may have loosened due to storage and shipping.
在安装期间，闸阀上的法兰垫圈螺栓应该重新紧固，因为在库存和运输时螺栓可能会松懈。
14.
" Tolerances for fasteners--Bolts, screws and nuts"
GB/T3103.1-1982紧固件公差螺栓、螺钉和螺母
15.
Reason for Low Tight Axle Strength of 10.9S Sets of Torshear Type High Strength Bolt for Steel Structures
钢结构用10.9S扭剪型高强螺栓连接副紧固轴力偏低原因分析
16.
Remove bolts holding shift lever to transmission.
拆卸将排挡杆固定到变速箱的螺栓。
17.
Fasteners--Clearance holes for bolts and screws
GB/T5277-1985紧固件螺栓和螺钉通孔
18.
Bolt( screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.
螺栓（钉、帽、头螺栓、簧垫圈、、珠轴承、柱轴承）最常用的机械零件。