1.
Remove excess solder with small brush while plastic( soft), leaving a fillet around end of valve as it cools.
在焊接部分成型后，用小刷子清除多余的焊料，使其在焊料冷却后形成一个环绕连接端口的圆角。
2.
Safety requirements for arc welding equipment--Part 1: Welding power sources
GB15579-1995弧焊设备安全要求第1部分:焊接电源
3.
The welding is so smooth that you can hardly see where the sections of pipe are joined together.
焊接处如此平滑，你几乎看不出是哪部分管道被焊接在一起了。
4.
Residual stress analysis of repair welding at different zone of Q345R welded joint based on finite element simulation
Q345R钢焊接接头不同部位补焊残余应力的有限元分析
5.
Investigation on the local mechanical properties of the automobile aluminium alloy welded joint
轿车用铝合金焊接接头局部力学性能分析
6.
The union of two metal parts by welding.
焊接把两个金属部件焊接为一个整体
7.
Safety requirements for arc welding equipment Part 12: Coupling devices for welding cables
GB15579.12-1998弧焊设备安全要求第12部分:焊接电缆耦合装置
8.
The Distribution Characteristics of the Local Mechanical Properties with the Aluminium Alloy Welded Joints and the Properties Study of T-type Tubular Joints;
铝合金焊接接头局部力学性能分布特征及T型管接头性能研究
9.
The parts of the crashed car had to be welded together in the garage.
汽车被撞坏的部分要在修车厂里焊接起来。
10.
Application of the twin-wire welding for robot central slot welding
机器人双丝焊在中部槽焊接上的应用
11.
Welding technology and microstructure of MIG welded magnesium alloy
镁合金MIG焊接工艺及焊接接头组织性能分析
12.
Welding Analysis and Research on Matching Welding Materials for Q460E Steel;
Q460E焊接性能分析及匹配焊材研究
13.
Optical Information Collection and Analysis of Welding Fume in MIG Welding
MIG焊焊接烟尘光电信息的采集与分析
14.
Study on elements distribution in weld seam of laser welding of aluminum alloys
铝合金激光焊接焊缝元素分布的研究
15.
3. Apply flux to outside of tube and inside of solder cup. Surfaces to be joined must be completely covered. Use flux sparingly.
3. 在管道的外面和焊接罩的内部涂上焊剂,焊剂必须完全覆盖焊接表面。请有节制地使用焊剂。
16.
apply flux to outside of tube and inside of solder cup. Surfaces to be joined must be completely covered. Use flux sparingly.
在管道的外面和焊接罩的内部涂上焊剂,焊剂必须完全覆盖焊接表面。请有节制地使用焊剂。
17.
The main body part is coiled by the aluminum tube, welded with copper pipe, copper capillary vessels.
主体部分由铝管盘成，焊接上铜管、铜制毛细管的蒸发器。
18.
Experimental Study on the Behavior of Partially Encased Composite Stub-columns Made with Welded H-section Steel;
焊接H型钢部分包裹混凝土组合短柱受力性能研究