1.
Do not open the card slot cover or press any camera buttons during the firmware writing operation.
固件写入过程中不要打开卡槽盖或按下任何相机按钮。
2.
Steel pipe blank flanges with tongue and groove face for PN 1.6MPa (16 bar)
GB/T9123.24-1988PN1.6MPa(16bar)榫槽面钢制管法兰盖
3.
Steel pipe blank flanges with tongues and groove face for PN 2.5MPa (25 bar)
GB/T9123.25-1988PN2.5MPa(25bar)榫槽面钢制管法兰盖
4.
Steel pipe blank flanges with tongue and groove face for PN 5.0MPa (50 bar)
GB/T9123.27-1988PN5.0MPa(50bar)榫槽面钢制管法兰盖
5.
Steel pipe blank flanges with tongue and groove face for PN 15.0MPa (150 bar)
GB/T9123.29-1988PN15.0MPa(150bar)榫槽面钢制管法兰盖
6.
Steel pipe blank flanges with tongue and groove face for PN 25.0MPa (250 bar)
GB/T9123.30-1988PN25.0MPa(250bar)榫槽面钢制管法兰盖
7.
Steel pipe blank flanges with tongue and groove face for PN 4.0MPa (40 bar)
GB/T9123.26-1988PN4.0MPa(40bar)榫槽面钢制管法兰盖
8.
Steel pipe blank flanges with tongue and groove face for PN 10.0MPa (100 bar)
GB/T9123.28-1988PN10.0MPa(100bar)榫槽面钢制管法兰盖
9.
Clip cable to cable guide at valve cover.
把电缆夹进阀盖上的电缆导槽。
10.
Design of cemented alloy circle stalk shaped cutter for turning shield groove
车防尘盖槽硬质合金圆柄成型刀设计
11.
"Spark-plug holes are provided, along with pockets into which the valves can move as they open."
气缸盖上留有火花塞口和凹槽,凹槽使气门打开时可以移动。
12.
Trim or remove excess sealant film in the rear main cap oil pan gasket groovDO NOT remove the sealant inside the rear main cap slots.
修整或清除后主盖机油底壳垫圈凹槽中过多的密封剂薄膜。切勿清除在后主盖槽中的密封剂。
13.
The surfaces of the lead plates were not hollowed out to cup toothless gums; they were flat.
铅制牙托的表面平坦，缺乏凹槽，无法覆盖牙床。
14.
The valve cover shall be held in place through the use of a single grooved style two-bolt coupling.
阀盖应该通过单个沟槽状双螺栓联结器固定住。
15.
A Comparison between the Saw-tooth and Tongue-groove Location of the Oblique Split Connecting Rod Cap
斜切口连杆盖锯齿定位及舌槽定位的分析比较
16.
Stability influence analysis on trench wall of seep proof screen in thick overburden layer
深厚覆盖层防渗墙槽壁稳定性影响分析
17.
and a little long hollow place I cut in the in-side of the boat, where I could lay gun, making a flap to hang down over it to keep it dry.
另外,我又在船舷内挖了一条长长的槽,用来放枪,还做了块垂板可盖住长槽,以防枪支受潮。
18.
Be sure the dummy club of the bar put into the restrict slot followed by tightening the fastening screws of cover plate
一定要将芯棒的凸台装入限位槽内，拧紧盖板紧固螺丝。