1.
" Rubber, vulcanized--Method for determination of strength properties of adhesive to metal in shear by tension loading"
GB/T13936-1992硫化橡胶与金属粘接拉伸剪切强度测定方法
2.
Effect of contents of Zn(MAA)_2 and Mg(MAA)_2 on insulation/metal adhesion
Zn(MAA)_2和Mg(MAA)_2用量对绝热层与金属粘接性能的影响
3.
Research on bonding between hydroxy-terminated polybutadiene rubber polyurethane elastomers and metal
端羟基液体橡胶聚氨酯弹性体与金属粘接的研究
4.
Study on the Heat Resistant Adhesives for Bonding Metals to Ceramics;
粘接金属与陶瓷的耐高温胶粘剂研究
5.
A Study for the Biomechanics of Metallic Orthodontic Bracket of Multiple Bonding;
金属托槽多次粘接的生物机械学研究
6.
Quantitative Detection of Adhesive Bond Quality Between Metallic and Nonmetallic Components Based on the Neural Networks
基于神经网络的金属与非金属材料粘接质量定量检测
7.
Elementary Research of the Factors Affecting the Shear Bond Strength of Metal Brackets to Porcelain Surfaces;
金属托槽与瓷面粘接强度影响因素的初步研究
8.
Blisters and other signs of improper adhesion, which expose bare metal, are not acceptable.
汽泡及因不适当的粘贴而引起的金属底材暴露是不可以接受的.
9.
It is also shown that the contact angle of water on the surface of the metallic material is a rather important factor influencing the adhesive force.
金属材料与液体间的固—液接触角是影响粘附力的较主要因素;
10.
Comparison of Shear Bond Strength of Resin and Metal Brackets with Different Adhesives in Vitro;
金属托槽与树脂托槽应用不同粘接剂抗剪切强度的体外研究
11.
The Effects of Sandblasting on Shear Bond Strength of Recycled Orthodontic Metal Brackets with Two Braket Base Design-an in Vitro Study;
不同底板脱落金属托槽经喷砂处理再粘接的体外实验研究
12.
Shear Bond Strength of Metal Brackets Bonded to Porcelain and Light-cured Composite Resin;
金属托槽与瓷、光固化复合树脂粘接抗剪切强度的实验研究
13.
The Influence of Two Primers on the Shear Bond Strength between Metal and Composite Resin
两种偶联剂在金属—复合树脂间剪切粘接强度影响的研究
14.
Effects of etching or no etching on the failure rates of second bonded metallic brackets
酸蚀与未酸蚀对不同时间金属托槽再次粘接后脱落率的影响
15.
Vienna metallic-cement amalgam
维也纳金属粘结用汞齐合金
16.
metal to-metal contact
干摩擦金属与金属直接接触
17.
Test method of cleavage strength of adhesive (metal to metal)
GB/T7749-1987胶粘剂劈裂强度试验方法(金属对金属)
18.
Very low viscosity oil for punching & stamping of ferrous & non ferrous material.
极低粘度金属加工油，适合黑色金属和有色金属的冲孔和冲压加工。