1.
Comparison of Effect of Strengthening Pedicle Screw Stability Through Partial and Integrated Solidification of Track in Vivo
钉道局部固化与整体固化增强椎弓根螺钉稳定性的体内比较研究
2.
Simulation on curing warpage deformation of composite T-shaped integrated structure
复合材料T型整体化结构固化翘曲变形模拟
3.
MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY EVOLUTION OF INTEGRALLY DIRECTIONALLY SOLIDIFIED Nb-SILICIDE-BASED ULTRAHIGH TEMPERATURE ALLOY
铌硅化物基超高温合金整体定向凝固组织和固/液界面形态演化
4.
Performance simulation of direct internal reforming solid oxide fuel cells
直接内部重整固体氧化物燃料电池的性能模拟
5.
Partial oxidation reforming of biomass raw gas over NiO-MgO solid solution monolithic catalyst
NiO-MgO固溶体蜂窝催化剂部分氧化重整净化生物质气特性
6.
Design and optimization of multi-stage solid launch rocket based on integrated stage concept
基于整体级概念的多级固体运载火箭设计与优化
7.
The Preparation and Characterization of Ce-Cu-O Solid Solution Catalyst and the Study on Oxidative Steam Reforming of Methanol;
铜一铈固溶体催化剂的制备、表征及甲醇氧化重整制氢的研究
8.
The outer mechanical seal shall be constructed with a solid block silicon carbide rotating seal face and a solid block silicon carbide stationary seal face.
外置的机械密封应该采用一块整体结晶碳化硅旋转密封面和一块整体结晶碳化硅固定密封面。
9.
The inner mechanical seal shall be constructed with a solid block carbon rotating seal face and a solid block silicon carbide stationary seal face.
内置的机械密封结构应该采用一块整体结晶碳旋转密封面和一块整体结晶碳化硅固定密封面。
10.
Dynamics Analysis and Optimization on Electromechanical Coupling System of Solid Rocket Motor Reshaping Machine Tool;
固体火箭发动机整形机床机电系统动力学分析与优化
11.
Study on Modeling and Control of a Direct Internal Reforming Solid Oxide Fuel Cell System
直接内部重整固体氧化物燃料电池系统的建模与控制研究
12.
Experimental Investigation on Methane Steam Reforming Over a Ni/YSZ Anode of Planar Solid Oxide Fuel Cell
平板式固体氧化物燃料电池Ni/YSZ阳极上甲烷重整过程实验研究
13.
Performance and Effective Kinetic Models of Methane Steam Reforming over an Ni-YSZ Anode of Planar Solid Oxide Fuel Cell
固体氧化物燃料电池阳极甲烷重整过程动力学模型
14.
Influence of Solid Acid Catalysts on Steam Reforming of Dimethyl Ether for Hydrogen Production
固体酸催化剂对二甲醚水蒸气重整制氢过程的影响
15.
Supporter and Immobilization Methods of Nano-TiO_2 Photocatalyst;
TiO_2光催化剂固定化载体及固化方法
16.
chemistry of solid-liquid interface
固体－液体界面化学
17.
To melt(a solid)by heating.
熔化通过加热熔化固体
18.
The mechanisms could be classified as sublimation , melt , thermal spalling , detachment of grains , vaporization , and spalling of grains adhered to the surface by resolidified phase .
将蚀除机理归纳为六种：升华、熔化、热剥离、整体颗粒移除、气化、再凝固粘附相的热削离。