1.
Study on Casting Material for Blast Furnace's Trough Made of Al_2O_3-SiC-C;
Al_2O_3-SiC-C质高炉出铁沟浇注料的研究
2.
The Practice of Transforming the Main Trough of Blast Furnaces with Single Taphole into Iron Store Structure with New Anti-explosive Castable Refractory
新型防爆铁沟浇注料与单铁口高炉出铁主沟储铁式结构改造实践
3.
The practice of on-the-spot casting of the iron runner at No. 10 BF of Anshan Iron & Steel Group Co.
鞍钢10号高炉现场浇注铁沟料实践
4.
Development of Ultra Low Cement Prefabricated Part for Fork Location of Blast Furnace Lander
高炉出铁沟岔口用超低水泥浇注料预制件的研制
5.
Research on Al_2O_3-SiC-C Castables for Blast Furnace Trough Strengthened by Sialon In-situ Synthesized;
原位生成Sialon增强Al_2O_3-SiC-C铁沟浇注料研究
6.
Study on Effect of Additives on Properties of Al_2O_3-SiC-C Castable for Iron Trough;
加入物对Al_2O_3-SiC-C质铁沟浇注料性能的影响
7.
Technological Design and Practice for Casting the NO.5 Blast Furnace s Slag/Iron Troughs;
武钢5号高炉渣铁沟浇注料工艺设计与实践
8.
Effect of Si_3N_4 addition on property of Al_2O_3-SiC-C castables for iron trough and runner
Si_3N_4加入量对Al_2O_3-SiC-C铁沟浇注料性能的影响
9.
Effect of binder on the properties of Al_2O_3-SiC-C iron trough castable
结合剂对Al_2O_3-SiC-C质铁沟浇注料性能的影响
10.
Effect of B_4C addition on mechanical properties of Al_2O_3-SiC-C based castables for iron trough
B_4C加入量对Al_2O_3-SiC-C铁沟浇注料力学性能的影响
11.
Synthesis of β-SiAION Composite Ceramics from Wasted Al_2O_3-SiC-C Castables and Coal Gangue
用后铁沟浇注料和煤矸石合成β-SiAlON-Al_2O_3复合材料的研究
12.
The Study on the Mullite Castable Used in Injection Lance;
铁水脱硫喷枪用莫来石质浇注料的研究
13.
Effects of Fe-Si_3N_4 Addition on the Mechanical Properties of MgO-based Castables
氮化硅铁加入量对镁质浇注料力学性能的影响
14.
DEVELOPMENT AND APPLICATION OF UNSHAPED REFRACTORIES FOR BF TROUGHS
高炉出铁沟用不定形耐火材料的发展与应用
15.
The series of current transformers are resin insulated， fully enclosed and busbar type. The iron core is circular and the secondary winding goes around the core before casting by epoxy.
本型电流互感器的铁心为圆环形，二次绕组匀绕制在铁心圆周上，用环氧树脂混合料浇注成形。
16.
The plexiglass product usually may divide into pours the board, squeezes out the board and the mold plastic.
有机玻璃产品通常可以分为浇注板、挤出板和模塑料。
17.
Square slabs were cut from cubes cast with various aggregate sizes.
从具有不同骨料粒度的立方浇注块中切出方形板块。
18.
Design of Injection Mold Gating System of the Plastic Gear Based on MoldFlow Software
基于MoldFlow塑料齿轮注射模浇注系统设计