1.
" Spacers for self-locking nuts,twolug, anchor"
GB/T962-1988双耳托板自锁螺母垫片
2.
" Spacers for self-locking nuts,angle, anchor"
GB/T963-1988角形托板自锁螺母垫片
3.
" Spacers for self-locking nuts,singlelug, anchor"
GB/T961-1988单耳托板自锁螺母垫片
4.
" Plain washers for bolts,screws and nuts--General plan"
GB/T5286-1985螺栓、螺钉和螺母用平垫圈总方案
5.
Flared type tube fittings--Back-up washer
GB/T5652-1985扩口式管接头锁紧螺母垫圈
6.
Tab washers for round nut
GB/T858-1988圆螺母用止动垫圈
7.
Stainless steel stuffing box hardware is standard (ie. bolts, gland studs, nuts, washers).
标准的金属密封不锈钢填料箱（如螺栓、填料压盖螺栓、螺母、垫圈）。
8.
Remove the mounting nut/washer assemblies and remove the column.
拆下转向柱装配螺母/垫圈总成，并拆下转向柱。
9.
Design of Nut Collars Sort System Based on Machine Vision
基于机器视觉的螺母垫圈分拣系统设计
10.
" Specifications of high strength bolts with large hexagon head, large hexagon nuts, plain washers for steel structures"
GB/T1231-1991钢结构用高强度大六角头螺拴、大六角螺母、垫圈技术条件
11.
A gasketed connection has four parts: the valve outlet, a nipple, a nut, and a gasket (or washer).
一个衬垫接头有四个零件：一个阀门排气口、一个管接口、一个螺母和一个衬垫（或垫圈）。
12.
Now we mainly produce in the fastener product the screw, the nut, from attack, filling piece, series the and so on ball pad product.
现在我们主要生产紧固件产品中的螺丝、螺母、自攻、平垫、弹垫等系列的产品。
13.
3-D and Nonlinear Finite Element Analysis for Tubesheet-Gasket-Flange-Bolt System Considering Hysteresis Effect of Gasket Material;
考虑垫片时滞效应的管板-法兰-垫片-螺栓连接系统的非线性三维有限元分析
14.
Gather the necessary installation tools: you will need a column cutter, column nuts, ferrules, a magnifying loop, and typewriter correction fluid.
收集必要的安装工具：柱切割器、柱螺母、垫圈、放大镜、打字机改正液。
15.
The bottom bolts will help locate gasket and hold it in position.
底部螺栓有助于对垫片进行定位,并保持恰当的位置。
16.
Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.
在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。
17.
Position the shims and striker on the (GOP) and install the bolts.
把垫片和车门闩眼定位在风栅口面板上，然后开始安装螺栓。
18.
Add sealed shim between the two flanges and then lock down the bolt.
安装时两法兰间需加密封垫片，然后均匀拧紧螺栓。