1.
Contrast study on the clinical effects of electrosurgical retraction and secondary gingival retraction
电刀排龈法与二次排龈法临床效果的对比研究
2.
Resolution to the Problem of Tool Disc Changer Lost
加工中心盘式刀库换刀子程序丢失的故障排除
3.
a sharp table knife used in eating steak.
吃牛排时使用的锋利的餐刀。
4.
Keep the line with a tray, put a knife, a fork and a piece of paper napkin on it.
拿一个盘子，放上刀叉、纸巾，排队。
5.
The steak was so tender, you hardly needed a knife to cut it .
那牛排真嫩，根本无需用刀切。
6.
Just pick up a tray, put a knife, a fork, a spoon and a paper napkin on it, and then start down the line.
先去拿餐盘，放上刀叉汤匙和餐巾纸，然后去排队。
7.
Just pick up a tray, put a knife, a fork, a spoon and a paper napkin on it, and keep the line.
只是拿一个盘子，放上刀、叉、勺子和纸巾，然后排队。
8.
And when he ate the roast chicken, instead of using a fork and knife, he picked a leg up with his fingers!
他吃铁排鸡，不用刀叉，把手拈了鸡腿起来咬！
9.
Research on Chip Removal and Cutting Tool Condition Monitoring Technology in BTA Deep Hole Drilling;
BTA深孔钻削排屑与刀具状态监测技术研究
10.
Hybrid algorithm of guillotine rectangular cutting problem
一种“一刀切”式矩形件优化排样混合算法
11.
the line of soldiers advanced with their bayonets fixed; they were arrayed in line of battle.
带着刺刀行进的一排战士；在战斗中，他们分排部署。
12.
On completion of the buttonhole the blade automatically cuts the center of the two rows of stitches.
锁完纽洞之后,刀片会自动地在两排针迹之间切开一道口子。
13.
Just pick up a tray, then put a knife, fork, spoon and a paper napkin on it and start down the line.
汤姆:只要拿一个盘子，把刀叉、匙子、餐纸放在盘子里，然后排队去取菜。
14.
After the rehearsal, the weary mechanic repaired the gears with shears and spear.
排练完后，疲倦的机修工用剪刀和矛修理了齿轮装置.
15.
Use a 5/8-inch drill bit, then a coarse cylindrical rasp to enlarge the drainage hole.
转一个5/8英寸的洞，然后用锉刀把这个“排水口”搞大点。
16.
Punch nesting understands tooling when nesting parts, not just a part's geometry.
对零件排版时,系统自动识别分配的刀具,而非仅识别零件图形.
17.
In a formal setting, you need to remove the corn from the cob with a steak knife and eat it with a fork.
正式场合里，你必须先用牛排刀切下玉米粒后，再用叉子舀起来吃。
18.
The Study on Gouge Detection and Tool Path Planning when Machining Free-form Surfaces Using Three Different Cutters;
对三种不同刀具加工自由曲面的干涉检查和路径安排的研究