1.
Top pouring is the simplest and cheapest method, but gives poor control over the rate of pouring.
上注法最简单，成本最低，但不好控制浇注速度。
2.
The molten metal may enter the ingot mould in two ways: from the top and from the bottom. Top pouring is the simplest and cheapest method, but gives poor control over the rate of pouring.
钢液注入钢锭模可采用两种方式:上注和下注。上注法最简单，成本最低，但不好控制浇注速度。
3.
Defects due to an unsatisfactory rate of teeming. This kind defects include splashing, rippled surface, and laps or folds.
由于浇注速度掌握不好而引起的缺陷。这种缺陷包括飞溅、波皱面以及重皮或摺叠。
4.
Influence of Pouring Temperature and Injection Speed on Microstructure and Hardness of Al-10%Si Alloy
压射速度和浇注温度对Al-10%Si合金组织与硬度的影响
5.
Effect of Pour Mode and Cooling Rate on Morphologies of Mg_2Si in AZ91-0.45Si Magnesium Alloy
浇注方式和冷却速度对AZ91-0.45Si合金中Mg_2Si形态的影响
6.
At the same casting speed, the eddy center is the lowest if the pouring angle is about 60° and the penetrating depth of molten steel flow increases with the increasing pouring angle.
在相同的拉坯速度下，随着浇注倾角的增大，钢液流股的穿透深度也随之增大。
7.
Then the liquild-surface in the case is decided by the matching relation of the flow of the leaning stove and the roll-casting speed 。
在实验铸轧系统中,前箱液位由倾动式电炉的浇注流量与铸轧速度的匹配关系决定。
8.
Effect of Heat Treatment Temperature on Properties of Lightweight Castable
热处理温度对轻质浇注料性能的影响
9.
After the first casting, the deflection can be checked and modified using shim plates.
第一次浇注混凝土后，挠度可用垫片调整。
10.
How much pouring temperature of EPC should be improved than that of sand mould casting
消失模铸造的浇注温度应比砂型铸造提高多少
11.
Study on Strength Properties of Phosphate Bonded Core Used in Investment Cast and Formed by Pouring
熔模铸造用浇注成形磷酸盐粘结型芯强度研究
12.
Difference between castable amount per unit volume and bulk density
耐火浇注料单位体积用量与体积密度的差异
13.
The influence of cast mold in rebound testing of concrete compressive strensth
浇注模板对回弹法检测混凝土抗压强度的影响
14.
Influence of Pore Size Distribution of Castable on Its Strength by Grey System Theory
浇注料孔径分布与强度关系的灰色系统研究
15.
Pore size distribution and its quantitative relationship with strength of corundum based castables
刚玉质浇注料孔径分布及其与强度的定量关系
16.
Effect of Heat Treatment Temperature on Property of Mullite-Bauxite Castable Refractory
热处理温度对莫来石-铝矾土浇注料性能的影响
17.
Effect of Heat Treatment Temperature on Properties of Calcined Flint Clay-Bauxite Castable Refractory
热处理温度对焦宝石-铝矾土浇注料性能的影响
18.
Research on Semi-Solid ZL101-Sc Alloy Prepared by Low Superheat Pouring
用低过热度浇注技术制备半固态ZL101-Sc铝合金