1.
Investigation of Fatigue Crack Deflection for A357 Casting Aluminium Alloy
A357铸造铝合金疲劳裂纹偏折研究
2.
Interaction between offset parallel cracks and combination conditions
平行偏置裂纹相互作用及其合并条件
3.
used of a break or crack or tear in bone or cartilage.
用来指骨头或者软骨的折断、有裂纹或者破裂。
4.
The morphology of crack propagation indicate that there is the toughening mechanism of whisker's pull- out and crack deflection.
裂纹进展形态表明,存在晶须拔出及裂纹偏转增韧机制。
5.
The Causes of Crankshaft Offset Grinding and Grinding Crack and Their Solutions;
曲轴偏磨与磨削裂纹的成因及解决办法
6.
Gerberich also used birefringent-coating technique to investigate the strain fields in cracked alummum plates. Gerberich
也曾用双折射涂层法研究了有裂纹铝板的应变
7.
Studies on the Crack Turning Theories for Integrally Stiffened Structures and It s Application;
整体加筋结构裂纹转折理论及其应用研究
8.
The fine grains, crack deflexion and grain-bridging are main toughening mechanisms of silicon carbide ceramic.
细晶、裂纹偏转和晶粒桥联是碳化硅陶瓷的主要增韧机制。
9.
Detailed siress analysis was carried out for a section of the pipeline including an eccentric reducer on which long cracks appeared twice.
进而对曾两次出现长裂纹的偏心异径管管段进行细部应力分析。
10.
Influence of Solute Segregation on Crack Susceptibility at Solidification Front of Continuous Casting Strand
溶质偏析对连铸坯凝固前沿裂纹敏感性影响的研究
11.
Distinguishing on Surface Laps and Cracks of Cold Heading Steel for Big Size Coils and Analyzing on their Forming Causes
大盘卷冷镦钢表面折叠、裂纹的判别及形成原因分析
12.
Using multiple-beam, we need not measure the tilt angle of Moire fringe, but record the position of the object when sharpness of the fringe is the best.
该法无需测量莫尔条纹偏折角,而是记录条纹对比度最好时试件的位置.
13.
seal-split cowhide bag
海豹纹理状裂纹牛皮袋
14.
Examine block for cracks or fractures.
测试泵体裂纹或破裂。
15.
The crack eventually caused the chord to fracture.
裂纹最终致使弦杆断裂。
16.
MICROSEGREGATION OF SOLUTE ELEMENTS IN SOLIDIFYING MUSHY ZONE OF STEEL AND ITS EFFECT ON LONGITUDINAL SURFACE CRACKS OF CONTINUOUS CASTING STRAND
钢凝固两相区溶质元素的微观偏析及其对连铸坯表面纵裂纹的影响
17.
Crack defect promotes crack initiation and growth.
裂纹缺陷促进了裂纹的萌生和扩展.
18.
The surface of steel wire shall not contain any oil, water or dirt and any defect of crack, knob, burr, rust, bend or scar.
钢丝表面应无油、无水、无污，并不得有裂纹、竹节、起刺、锈蚀、折弯和伤痕等缺陷。