1.
Improvement of Stud Welding Process And Increase Qualified Rate of Welding
改进栓钉焊接工艺 提高焊缝一次合格率
2.
However, the stud welding roots in the negative moment region of the beam are often subjected to the joint action of shear stress cycling of the studs and tensile stress cycling of steel girder flanges.
但在负弯矩处栓钉焊趾往往承受栓钉剪应力循环和钢梁翼缘拉应力循环的共同作用。
3.
Sweat Solder adapter with Cover Tube and Cast Set Screw Wall Flange
焊接焊料适配器含盖管和铸造固定螺栓墙法兰
4.
Research on Welding Technology of Alkaline Battery Current Collector and Welding Inverter Power Supply;
碱性电池负极钉焊接技术及逆变焊接电源的研究
5.
Design Method of the Headed Stud Embedded at the Pinned Joint of Steel Beam to Concrete Wall
钢梁-混凝土墙铰接节点栓钉预埋件的设计计算
6.
Analysis on Stud Connectors in Steel and Lightweight Aggregate Concrete Composite Beams
钢-轻骨料混凝土组合梁栓钉连接件承载力分析
7.
Numerical analysis of stud shear connectors in SRHPC structures
栓钉剪切连接件在SRHPC结构中的数值分析
8.
Experimental studies on behavior of stud shear connectors under monotonic loads
单调荷载下栓钉连接件受剪性能试验研究
9.
Study on Square Box Bolt Welding Girder Steel Bridger Interface Friction-increasingcoat;
方箱式栓焊梁钢桥梁连接面增摩涂层的研究
10.
Headless studs for stud welding
GB/T10432-1989无头焊钉
11.
Component installation of nodes connected by bolts or welding required inspection Connections after passing before welding or fastening.
构件安装采用焊接或螺栓连接的节点,需检查连接节点,合格后方能进行焊接或紧固.
12.
Frame of front-wheel double-drum component: It is of formed steel welding structure，which is connected with main frame by bolts.
前轮双转鼓组件框架：型钢焊接结构，通过螺栓与主框架连接。
13.
Butt welded 1;Butt welded 2;Butt welded 3;Butt welded 4
对接焊接 1;对接焊接 2;对接焊接 3;对接焊接 4
14.
Fracture Mechanism, Cyclical Performance and Design Recommandations of Welded Flange-Bolted Web Beam-To-Column Rigid Connections in Steel Moment Frames under Seismic Load;
钢框架梁柱栓焊刚性连接的滞回性能、破坏机理及抗震设计建议
15.
Mechanical Behavior of Bolt-weld Joints between Square Concrete-filled Tubular Column and Reduced Beam Section
方钢管混凝土柱—削弱钢梁端栓焊连接节点受力性能
16.
To fasten or plug with a peg or pegs.
钉木钉，用木钉钉牢用一个或几个钉栓锁住或插上
17.
Cheese head studs for stud welding
GB/T10433-1989圆柱头焊钉
18.
Solve the daily quality issue, especially at welding, clinching, tapping, riveting, silkscreen, paint, final assy, testing, packing station.
解决每天的质量问题,特别是焊接,铆接,攻丝,抽铆钉,丝印,喷漆,总装,测试,包装.