1.
Results indicated that, within certain range, the joint strength increased with the increase in weld thickness.
试验发现,在一定钎缝厚度范围内,随着钎缝厚度的增加,接头强度随之提高.
2.
This paper analyses the cause of strength descent of brazing weld, and proposes improving measures.
本文分析了钎焊焊缝强度下降的原因,并提出改进措施。
3.
"Where thickness characteristics at the joint are more important than strength, a thinner welder is possible at reduced joint strength. "
如果焊缝的厚度比强度更重要,则在降低强度条件下可使焊缝更
4.
Research the Influence on Mechanics Performance of Jointing Techniques Parameter
钎焊工艺参数对钎缝组织性能影响的研究
5.
Feasibility of measuring palate bone thickness and bone mineral density using spiral computed tomography
螺旋CT测量腭中缝骨厚度及骨密度的可行性
6.
Phase Constitution of Soldering Seam and Mechanical Properties of Zn Matrix Filler Metal Soldering Magnesium Alloy AZ31B Joint
Zn基钎料钎焊镁合金AZ31B接头的钎缝物相及力学性能
7.
Transfer Behavior Study in Weld Thickness Direction of the Welding Plastic Metal in Friction Stir Welding
搅拌摩擦焊焊缝塑性金属在焊缝厚度方向的迁移行为研究
8.
Application of Multizone Ultrasonic Inspection for Great Thickness EBW
应用超声多区聚焦技术检测大厚度电子束焊缝
9.
Spatiotemporal shaping and filtering of terahertz pulses through metal slits with finite thickness
有限厚度金属狭缝对太赫兹脉冲的整形和滤波
10.
Research on Weld Toughness of X80 Heavy Section Pipeline Steel at Different Welding Speeds
X80厚壁管线钢不同焊接速度下焊缝韧性研究
11.
The Comparisons of Brazed Joint Microstructures between Homemade and Imported Brazing Filler Alloy
国产耐热合金钎料与进口钎料焊缝组织对比分析
12.
Weldability and Microstructure of Copper Joints Welded by Two Kinds of Phosphor-copper Brazing Filler Metal
两种铜磷钎料对紫铜钎焊的焊接性能和焊缝组织对比
13.
Study on Clearance Filling Ability and Interfacial Structure of 316L Stainless Steel Brazed Joint Using BNi-2+BNi-5 Composite Filler
BNi-2+BNi-5复合钎料钎焊不锈钢填缝能力及其组织性能研究
14.
The application of the said gauging system will be capable of strongly ensuring production of high accuracy seamless steel tubes.
应用该测厚系统，可为生产高精度无缝钢管提供强有力的保证。
15.
To reduce bulk, trim interfacing within seam allowances to 1.3cm(1/2 inch)
为了减少厚度,将缝份处的衬布修剪掉1.3cm(1／2英寸)。
16.
"High strength steels may result in increased thickness, however, the resulting joint is strong, smooth and recoilable. "
高强度钢可能更厚些,但是,焊缝是强固的,平滑的,可重卷的。
17.
Sewing Machine Needles: sized from fine to heavy. They should conform to the weight and type of fabric used.
缝纫机针：由细到粗编号,选用时应与所用面料的厚度及类型相一致。
18.
A tape or covered cord sewn into a seam as reinforcement or trimming; welting.
滚条，叠边缝在褶中用来加强厚度或装饰的线带或包起来的线；革条