1.
Wave Mode Conversion on Welding Ultrasonic Testing for Middle or Thick Plate
中厚板焊缝超声波探伤中的波型转换辨析
2.
Forming limit and weld seam movement of TWBs with different thicknesses in square cup
差厚拼焊板拉深方盒形件成形极限及焊缝移动
3.
Control of Uniforming Compositions for the Large Thickness Joints of the Titanium Alloy
厚板钛合金电子束焊缝的成分均匀性控制
4.
Study on the Welded-line Movement of Square Cup Using TWBs in Hydro-forming Deep Drawing
差厚拼焊板方盒形件充液拉深中焊缝移动的研究
5.
Weld-line Movement and Factors Affecting Formability for Different Thickness Tailor-welded Blank of Square Cup
差厚拼焊板盒形件成形影响因素及焊缝移动规律
6.
Study on Weld-line Movement of Square Cups with Tailor-welded Blanks in Hydro-forming Deep Drawing
差厚拼焊板方盒件在充液拉深过程中焊缝移动的研究
7.
Wavelet Theory Based Study on Ultrasonic Testing Analyses in Thick-plate Austenitic Stainless Steel Welds;
小波理论在厚板奥氏体不锈钢焊缝超声波检测中的应用研究
8.
Decrease the weld number as possible: Choosing the right thickness of steel plate can reduce the rectification amount after welding!
尽可能的减少焊缝数量：适当选择板壁的厚度，可减少焊后变形矫正量。
9.
Transfer Behavior Study in Weld Thickness Direction of the Welding Plastic Metal in Friction Stir Welding
搅拌摩擦焊焊缝塑性金属在焊缝厚度方向的迁移行为研究
10.
Quality Control of the Fillet Weld in the Tube and Tube Sheet of Heat Exchanger
换热器管-管板角焊缝焊接质量的控制
11.
Weld Seam Movement of Magnesium Alloy Tailor-welded Blanks during Deeply Drawing
镁合金拼焊板拉深成形焊缝移动规律
12.
Research on Welding Characteristics of EH36 Steel by Using Double-Sided Arc Welding
EH36钢厚板双面双弧立焊焊接特性研究
13.
Application of CO_2 Gas Protective Welding to Medium Thickness Plate
CO_2气体保护焊在中厚板焊接中的应用
14.
Judge of Transverse Crack of Thick-Walled Seam by Ultrasonic Testing Method
厚壁焊缝横向裂纹的超声波判别方法
15.
Research on Weld Toughness of X80 Heavy Section Pipeline Steel at Different Welding Speeds
X80厚壁管线钢不同焊接速度下焊缝韧性研究
16.
Microstructure and performance of friction stir welding in 6063 aluminum alloy
5mm厚6063铝合金搅拌摩擦对焊焊缝组织分析
17.
"Where thickness characteristics at the joint are more important than strength, a thinner welder is possible at reduced joint strength. "
如果焊缝的厚度比强度更重要,则在降低强度条件下可使焊缝更
18.
The backing plate shall be welded with matching electrodes so that the weld on the clad side is flush with the backing plate surface.
底板用配套焊条焊接，使复层侧的焊缝与背衬板表面齐平。