1.
Dynamic Anti-plane Behavior of the Interaction between a Crack and a Circular Inclusion in a Piezoelectric Medium;
压电介质中圆柱夹杂与裂纹的动力反平面相互作用
2.
The Interaction of Circular Cavity, Inclusion with Beeline Cracks by SH-wave;
SH波作用下孔洞、夹杂与直线形裂纹的相互作用
3.
Investigations on the Interaction between Dislocations and Cracks/Inclusions with Imperfect Interface;
位错与裂纹/含非理想界面夹杂的干涉机理研究
4.
INVESTIGATION TO BIMATERIALS INTERFACE CRACK WITH INCLUSTION;
含夹杂两相材料界面裂纹问题的研究
5.
THE IMPACT OF NONMETALLIC INCLUSION ON GENERATION OF FORGING CRACK
非金属夹杂物对锻造裂纹形成的影响
6.
Interaction among a Screw Dislocation, Interfacial Crack and Inclusion under Uniform Heat Flux;
均匀热流场中螺型位错、界面裂纹与夹杂的相互作用
7.
Interaction between Screw Dislocation and Circular Imperfect Interface with Crack in Piezoelectric Materials
压电材料中螺型位错与含裂纹非理想界面圆形夹杂的干涉效应
8.
Scattering of SH-Wave by a Semi-Cylindrical Hill Above a Subsurface Inclusion and Crack;
SH波对夹杂裂纹附近半圆形凸起的散射
9.
Study on Crack Growth Life of Powder Metallurgy Superalloy Turbine Disk Containing Inclusions;
含夹杂粉末高温合金涡轮盘裂纹扩展寿命研究
10.
Effects of Piezoelectric Particle on the Three-dimension Crack-tip Stress Fields of Near Crack;
压电圆柱形夹杂对邻近裂纹三维应力场的影响
11.
The Contact Problem of FGM with Crack Mingled with Elastic Material
弹性材料夹杂含裂纹梯度材料的接触问题
12.
The surface of nickel/plate should be smooth and neat without interlayer, crack, peeling, bubble and foreign substance.
带材/片材表面应光滑、清洁。不应有分层、裂纹、起皮、气泡和夹杂。
13.
Scattering of SH-Wave by an Interface Cylindrical Elastic Inclusion with Diametrical Cracks;
含有径向裂纹的界面圆形弹性夹杂对SH波的散射
14.
Large deformation bands were observed at each side of the crack.
实验结果表明：在裂尖两侧存在与裂纹方向夹角约为50°大变形带。
15.
The results showed that the major cause of longitudinal surface cracking of20 steel tube blanks was higher nonmetallic inclusion content in the steel than standard value.
结果表明:非金属夹杂物超标是导致管坯表面产生纵向裂纹的主要原因。
16.
Analysis of the Coalition and Interference of High Temperature Low-cycle Short Fatigue Crack under Complex Stress Condition;
复杂应力状态下高温低周疲劳短裂纹合体与干涉行为研究
17.
Propagation and Environmental Propagation of the Indentation Crack of Ferroelectric Materials;
铁电材料压痕裂纹的开裂与环境开裂
18.
After cutting, shear section shall be checked for no lamination and shear crack.
切割后，应检验切割部分有无夹层，切割裂纹。