1.
Interior Point Algorithms and a Smoothing Newton Method for the Second-order Cone Programming;
二次锥规划的内点算法及光滑牛顿法
2.
Under mild assumptions on the inexactness, we can find an e-approximate solution of the SOCP by using this algorithm.
在相对不精确的假设下，利用该算法可找到二次锥规划的ε-近似解。
3.
A primal-dual inexact infeasible interior-point algorithm for the second-order cone program (SOCP) was presented.
给出了二次锥规划的一种非精确不可行内点算法。
4.
A matrix-splitting method for symmetric affine second-order cone complementarity problems;
一个求解对称仿射二次锥互补问题的矩阵分解方法
5.
Two Theorems for the Real Line from the Crossing of Plane and Quadratic Cone and Their Application
有关平面与二次锥面相交成实直线两个定理及其应用
6.
Based on the optimality conditions and complementarity conditions for SOCP, a new merit function is defined in the algorithm.
基于二次锥规划的最优性条件和互补条件，定义了一个新的价值函数。
7.
Study On The Oblique Dimetric Projection Of The Hyperconical Surface In Four-Dimensional Space And Its Orthographic Projections Upon The Four Three- Dimensional Projection Spaces;
E~4中二次锥型超曲面立体图及其在三维投影空间正投影图的研究
8.
tangent-cone of a qualric
二次曲面的切线锥面
9.
Development of AutoCAD on labeling taper and pitch according with chinese national standard used ARX
AutoCAD锥度、斜度国标标注的ARX二次开发
10.
A Smoothing Newton Method for a Type of Inverse Quadratic Programming Problems with Second Order Cone Constraints;
二阶锥约束二次规划逆问题的光滑牛顿法
11.
An Augmented Lagrange Method for a Type of Inverse Quadratic Programming Problems with Second-order Cone Constraints;
二阶锥约束二次规划逆问题的增广Lagrange方法
12.
Parametric Design of Spiral Bevel Gear Based on Secondary Development of UG System;
基于UG二次开发的弧齿锥齿轮参数化造型
13.
SHG-CD and Third-Order Nonlinear Effect of Tripod-Like Chiral Molecule
三角锥型手性分子二次谐波圆二向色性及三阶非线性效应
14.
Theoretical Calculation of Wave Aberration for Cassegrain Bimirror System at Limited Distance
二次圆锥曲面卡塞格林系统有限目标距离波象差的理论计算
15.
Parametric Design and Second Development of Bevel Gear Differential Based on UG
基于UG锥齿轮差速器的参数化设计及其二次开发
16.
Three-sample-and-two-time Iteration Algorithm Optimality of Rotation Vector in Coning Motion
锥运动环境下旋转矢量的三子样二次迭代优化算法
17.
Analyzing the finger conical second enveloping ring-surface worm transmission by the fitting theory, the general mathematical model is put forward Modifing( a a angle add( I formation can eliminate oringinal arranging dense contact wire gear surface.
通过对指状锥面二次包络环面蜗杆传动进行啮合理论分析，提出了标准传动的通用数学模型。
18.
The Research on the Limit Parameters for One-Operation Forming the Conical Part in Deep Drawing;
圆锥形零件一次成形极限参数的研究