1.
It was an extensional and faulted basin i n Mesozoic,and then developed into an intermountain basin with compressed strik e-slip attribute in Cenozoic.
分析认为中生代盆地具“伸展断陷盆地”特征,而新生代盆地演化为“挤压走滑型山间盆地”。
2.
The Altun fault experienced an intracontinental cycle of extension-compression during Neogene in a background of sinistral strike-slipping.
新近纪阿尔金断裂在左行走滑的大背景下经历了一个陆内的拉张—挤压旋回。
3.
Sejournet extrusion process
赛茹尔内玻璃润滑热挤压法
4.
THE HYDRODYNAMIC LUBRICATION RESEARCH ON THE PROCESS OF HYDROSTATIC EXTRUSION;
静液挤压过程中的流体动力润滑研究
5.
Study of Squeezed Gas Film under Second-order Slip Boundary Condition
二阶边界滑移气体薄膜挤压特性研究
6.
Boundary parameters during glass lubricated hot extrusion of steel pipes
钢管玻璃润滑热挤压工艺的边界条件
7.
Study on lubricants and cooling method for warm extrusion
温挤压加工中润滑剂与冷却方式研究
8.
Study on the Lubricating Properties of Lubricating Oils with Nanoparticle Additives in the Hot Extrusion of LY12
热挤压润滑油用纳米润滑添加剂润滑性能的研究
9.
On the Behavior of Squeeze Film Lubrication of Journal Bearings with Micropolar Fluids
微极性流体润滑的挤压膜轴承特性研究
10.
Improved design and research of die unloading installation in cold extrusion die of spherical slippery footstep
球面滑履冷挤压模脱模装置的改进设计研究
11.
Squeeze Effect of a Parallel Surface Bearing with Tailored Boundary Slippage
定制边界滑移平行轴承的挤压效应(英文)
12.
Extrusion force of HHE can be minimized and the disfigurement of extrusion products can be avoided when the viscosity of the medium is proper.
挤压介质的粘度是关系到坯料变形流动的润滑性能及挤压变形流动性能的关键。
13.
hydrostatic extrusio
静水压挤压;静水压挤压;静液力挤压;静液力挤压;液力静挤压
14.
a machine that smoothes or glazes paper or cloth by pressing it between plates or passing it through rollers.
通过在金属盘中挤压或通过滚筒使得纸或衣物光滑的机器。
15.
Research and practice of big lead angle rotating unloading method for precise cold extrusion die of spherical slippery footstep
球面滑履精密冷挤压大升角旋转脱模方法研究与实践
16.
Numerical Simulation of Fluid-Solid Coupling for Lubricating Oil Extrusion Process Between Cylinder and Piston with Micro-pits
凹坑表面活塞与缸套挤压润滑油的流固耦合数值模拟
17.
Influence of Slip Length of Gas-Assisted Extrusion Die on Pressure Drop and First Normal Stress
气辅挤出口模中滑移段长度对压力降和第一法向应力差的影响
18.
Low of slippage on contact surfaces in squeeze flow of power-law fluid between two parallel disks
两平行刚性圆盘挤压幂律流体时接触面的滑移规律