1.
On Exchange Order of Repeated Limits of Real-Valued Column;
![点击朗读](/dictall/images/read.gif)
关于一类实数列累次极限的交换次序
2.
Applied the Functional Sequence’s Limit Theorem and the Repeated Limit Theorem to the Exchange Order Theorem of Repeated Integral
应用函数列的极限理论和累次极限对累次积分换序的处理
3.
By using the concept of uniform limit, several conditions for exchanging order of repeated limit were esta blished and several results were also acquired.
利用一致极限概念,建立了累次极限的几类换序条件,得到若干结果。
4.
to the nth degree [power]
![点击朗读](/dictall/images/read.gif)
⑴至n次[乘幂]⑵无限地;到极点,极度地
5.
The strong limit theorems for finite nonhomogeneous Markov chains;
![点击朗读](/dictall/images/read.gif)
有限非齐次马尔可夫链的强极限定理
6.
rated instrument limit primary current
![点击朗读](/dictall/images/read.gif)
仪表的额定极限一次电流
7.
A strong limit theorem for nonehomgenous Markov chain
![点击朗读](/dictall/images/read.gif)
关于非齐次马氏链的一个强极限定理
8.
In this paper, the problem of limit cycle for a cubic system is studied.
![点击朗读](/dictall/images/read.gif)
讨论三次系统(方程式略)的极限环问题。
9.
The Research on the Limit Parameters for One-Operation Forming the Conical Part in Deep Drawing;
圆锥形零件一次成形极限参数的研究
10.
The Boundedness and Limit Cycle for a Class of Cubic Kolmogorov Type System;
![点击朗读](/dictall/images/read.gif)
一类三次Kolmogorov型系统的有界性及极限环
11.
Some Strong Limit Theorems for Hidden Nonhomogeneous Markov Models
![点击朗读](/dictall/images/read.gif)
隐非齐次Markov模型的若干强极限定理
12.
On the number of limit cycles of a Z_4-equivariant septic polynomial system
![点击朗读](/dictall/images/read.gif)
Z_4等变七次多项式的极限环数目(英文)
13.
Existance and Non-existance of Limit Cycle in the Fourth Quadrant of a Class of Cubic System;
一类三次系统在第四象限极限环的存在性
14.
Limit cycle of Hamilton system under quadratic perturbation
![点击朗读](/dictall/images/read.gif)
一类二次Hamilton系统在二次扰动下的极限环
15.
The distribution of limit cycle in a cubic system with seven-order perturbed term
![点击朗读](/dictall/images/read.gif)
一类具有七次扰动项的三次系统极限环分支
16.
Hopf bifurcaion of a multiplier-accelerator model with progressive income tax and parameter interval of limit cycle existence;
累进所得税的乘数-加速模型的Hopf分支与极限环存在的参数区间
17.
Study on Forming Conditions for One-Operation Deep Drawing in Conical Part of Thin Wall;
![点击朗读](/dictall/images/read.gif)
薄壁锥形件一次拉深成形极限条件研究
18.
The Research of Approach to Predict the Maximum Length of One-step Drawing;
![点击朗读](/dictall/images/read.gif)
板料一次拉深极限高度预测方法的研究