1.
Angle cut: To cut paper to special angles in order to avoid waste in the manufacture of enveloped.
斜角切:在制造信封时，把纸张作特别角度裁切，以减少损耗。
2.
Steel Bar with different specifications to match the length of the length overall layout; Should continue l0 ng expected, by cutting short expected to reduce short head, reducing wear and tear.
将同规格钢筋根据不同长度长短搭配,统筹排料;应先断长料,后断短料,减少短头,减少损耗.
3.
Oil loss can be reduced by taking corresponding measures in deacidification of rice bran oil.
在生产中应采取针对性措施控制损耗，达到减少油脂损耗的目的。
4.
A gradual diminution in number or strength because of constant stress.
消耗，耗损，削弱指因不断的压力而使数量或力量逐渐减少
5.
A quantity or portion of something lacking after delivery or storage.
减耗量物品的储运损耗部分或损耗量
6.
Only replacing the damage and deformation ciner in use, can reduce spillage of material thus lower its cost.
在使用损坏变形后，只需更换内衬，减少了材料损耗，降低了成本。
7.
This will minimize line wear by distributing stem and disc weight evenly.
这样可以减少由于均衡分散阀杆与蝶板重量所造成的管道损耗。
8.
Insulate your home. Cavity wall insulation can cut heat loss through the wall by up to 60 percent.
房屋隔热可以利用空心墙来减少热能损耗，降幅高达60%。
9.
Calculation of Electric Loss on the Shield for Canned Inductive Motor and the ways of its Reduction
屏蔽式感应电动机屏蔽套损耗的计算及减少途径
10.
it requires 97 percent less energy,
能量消耗会减少97%，
11.
consequential (loss, damage, reduction)
间接（损失、损害、减少）
12.
A gradual, natural reduction in membership or personnel, as through retirement, resignation, or death.
人员耗损，减缩人员指逐渐的、正常的成员或人员的减少，如退休、辞职或死亡
13.
Following the reduction of water withdrawal the water consumption decreases and the decrease rate tends to diminished.
随着取用水量的减少，耗水量也逐渐减少，但减少幅度越来越小。
14.
That's not all, the acceleration on start-up has a massive impact on the electricity supply charges, and in turn this also leads to heat losses dramatically reducing the life of the motor.
不仅如此，启动加速会对供电系统产生强烈冲击，并因此而导致热损耗并减少马达寿命。
15.
Concentrated on oil consumption, deposit and soot dispersion control plus ring wear protection.
主要致力于减少润滑油耗油量，沉积物，进行烟灰控制和活塞环磨损保护。
16.
The problem of reducing the wear of cutting tools and eroders (the tools applied in erosion processes) also plays its part.
减少切削刀具和腐蚀器(在腐蚀加工中所用的工具)的损耗同样也很重要。
17.
The paper introduces the application of lubricating and sealing technology of rolling bearing, which can reduce the loss of bearing and the rate of accident in routine production.
通过介绍滚动轴承润滑与密封技术的应用,使得减少日常生产中轴承的损耗,降低事故的发生率。
18.
Radiation losses are minimised by use of a well insulated locking swing– aside cover that can be sealed when no baling is needed.
转动式盖以优质绝热材料制成，在无须舀出和装料时能够密封熔炉，使热量损耗减少到最低。