1.
Investigation on warm/hot hydro-forming of high strength aluminum alloy sheet
高强度铝合金板材的温热介质充液成形研究
2.
Abstract: The design consideration and functional principle of hydraulic control system, which is used for a devise for hydro-mechanical drawing of sheet metal on a general hydraulic press, are introduced.
文摘:介绍了用于通用液压机上的板料充液成形装置液压控制系统的设计思想及工作原理。
3.
Optimization for hydroforming blanks of a car beam based on the Grey system theory
基于灰色系统理论的汽车横梁充液成形用坯料优化
4.
Effects of Prebulging on Hydromechanical Deep Drawing of 2A12 Alluminum Alloy Complex-shaped Components
预胀对2A12铝合金复杂曲面零件充液拉深成形的影响
5.
If a liquid food is cooled with sufficient agitation, ice crystals nucleate and grow, and a slurry of relatively pure ice crystals in a concentrate can be obtained.
如果冷却液体食品并充分搅动,那么冰晶会形成冰核并增长,最终会在浓缩液中得到较纯的冰晶。
6.
An early embryonic form produced by cleavage of a fertilized ovum and consisting of a spherical layer of cells surrounding a fluid-filled cavity.
囊胚由分裂受精卵产生的早期胚胎外形，由围绕充满液体的洞的球形细胞层组成
7.
Influence of liquid on vibration characteristics of boxed multi-tanks structure
充液对箱形多腔结构振动特性的影响
8.
Study on liquid pressure loading paths of square cup in Hydro-mechanical deep drawing without draw die
盒形件无模充液拉深液压加载路径的研究
9.
These orient themselves so that a fluid-filled cavity, the blastocoel, forms inside the mass of cells.
这些细胞进行自我调整，以致在细胞群内部形成一个充满液体的腔，即囊胚腔。
10.
Research on the Effects of Glutamine and Soybean Peptide Supplementation on the Structure of Kidney Filtration Barrier and Component of Urinary of Over-training rats;
补充谷氨酰胺和大豆多肽对过度训练大鼠肾脏滤过屏障形态结构和尿液成分影响的研究
11.
Effects of Glutamine and Soybean Peptide Supplementation on the Structure of Kidney Filtration Barrier and Component of Urinary of Over-training Rats
补充谷氨酰胺对过度训练大鼠肾脏滤过屏障形态结构和尿液成分的影响
12.
The process of forming and falling in drops.
形成液滴和滴落的过程
13.
The severed fluid may form a drop or may form an unstable ligament which will later break up into drops.
分裂的流体可以形成液滴，或者形成不稳定的液带，随后破裂成液滴。
14.
The Hydroforming of Square Parabolic Reflector of Auto;
矩形抛物线车灯反光镜充液拉深实验研究
15.
Research on the Cylindrical Cup by Hydrodynamic Deep Drawing Based on Numerical Simulation
基于数值模拟的锥形件充液拉深工艺研究
16.
Numerical Simulation of Process of Square Cup Drawing Using Tailor Welded Blanks in Hydro-mechanical Deep Drawing Without Draw Die
拼焊板盒形件无模充液拉深工艺及数值模拟
17.
The formation reasons and filling behaviors of the beads in top injection and side injection were analyzed.
对两种射料充填形态的形成原因和充填特性进行了分析和比较。
18.
a graceful but not yet fully perfected literary style.
优美但未充分形成的文学风格。