1.
The optimal technique parameter mensuration of sodium fluoride adsorb hydrogen fluoride
氟化钠吸附氟化氢最佳工艺参数测定
2.
The Experimental Study on Damp and Hot Buckwheat Drying Technology and Optimum Parameters;
湿热荞麦干燥工艺及最佳工艺参数的试验研究
3.
Affecting factors and the optimum technological parameters in waste particleboard liquefaction
废弃刨花板苯酚液化的影响因素及最佳工艺参数
4.
The Meathod of the Steepest Ascent and the Determination of Optimal Technical Operating Parameters
最陡坡法与最佳工艺操作参数的确定
5.
The Study on the Best Content for the Film and the Technical Parameter;
缓释肥料最佳膜组分及加工工艺参数研究
6.
Study on gasification wastewater treatment by SBR process
SBR工艺处理煤气废水的最佳运行参数研究
7.
The process for the treatment of the waste acid from crude benzol refining with calcining process is studied, the optimum operation data are discussed and the process is optimized.
研究了焙烧法处理粗苯精制废酸的工艺过程,探讨了最佳运行参数,优化了工艺流程。
8.
Research on the Best Parameter of Shendong Mine Fully Mechanized Face;
神东矿区综采工作面最佳参数的研究
9.
The technological parameters for producing good quality coated glass at low pull out rate were optimized.
通过生产实践,获得了低拉引速度下产品质量好,生产周期较长的最佳镀膜工艺参数。
10.
Meanwhile the optimal welding parameter which was suitable for welding line impact toughness was gained by analysis on the test result of impact toughness and microstructure.
通过对冲击韧性的测试结果与微观组织的分析,确定出使焊缝冲击韧性最佳的焊接工艺参数。
11.
ObjectiveTo explore the optimal purification condition of total flavonoids from Bidens bipinnata L.with macroporous resion.
目的研究大孔吸附树脂富集纯化鬼针草总黄酮的最佳工艺条件及参数。
12.
Study on Three-parameter Optical Shift Schedule and Control Method of Construction Vehicle
工程车辆三参数最佳换挡规律及控制方法研究
13.
OBJECTIVE: To optimize the prescription and preparation of matrine liposomes.
目的:筛选苦参碱脂质体的最优处方和最佳制备工艺。
14.
A Study on Optimum Composition and Optimum Plating Progress of (Ti,Al,Zr)N Super-Hard Reactive Films;
（Ti，Al，Zr）N膜最佳成分及最佳工艺的研究
15.
Establishing a Mathematical Model of an Optimum Technological Parameter of Siro-spinning;
建立赛络纺纱最优工艺参数的数学模型
16.
t invariant estimate of location parameter
局部参数的最佳不变量估计;局部参数的最佳不变量估计
17.
THEOREITICAL STUDY ON OPTIMIZATION OF OPERATING PARAMETERS IN OPTICALLY PUMPED CAVITY NH_3 SMMWLASER;
光泵腔式NH_3分子亚毫米波激光器最佳工作参数的理论研究
18.
Optimization of Molding Processing Parameters for Automobile Bumpers Based on Minimization of Sink Index
基于缩痕最小的汽车保险杠成型工艺参数优化