1.
AAA Bearing LTD offers Offers to Tapered roller bearings, thrust ball bearing and Self-aligning bearing.
公司提供大量的摆动轴承、自动调心轴承和夹紧套筒。
2.
reel gripper jaws
卷取机卷筒的夹紧爪
3.
Finite Element Simulation of the Thin-wall Hydraulic Cylinder's Clamping Deformation
薄壁液压缸筒夹紧变形的有限元模拟
4.
Sleeve 1;Sleeve 2;Screwed sleeve 1;Screwed sleeve 2
套筒 1;套筒 2;螺纹套筒 1;螺纹套筒 2
5.
Grip the sleeve and the piston assembly by the head of the hex head bolt.
用六角头螺栓的头部夹住套筒和活塞总成。
6.
Three-dimensional Finite Element Analysis of Fixed, Removable Partial Denture and Telescopic Crown as Periodontal Splints;
固定、可摘及套筒冠牙周夹板的三维有限元研究
7.
Analysis and Check on the Design Pressure of the Tube Body of WHF Lined Case Reaction Kettle
WHF型夹套反应釜筒体设计压力分析和校核
8.
Sleeve 1;Sleeve 2;Sleeve 3;Screwed sleeve 1;Screwed sleeve 2
套筒 1;套筒 2;套筒 3;旋拧套筒 1;旋拧套筒 2
9.
The company fujian fulong industrial co. offers among other Reverse osmosis.
提供关于逆渗透以及套筒、夹头卡盘、滤尘管、药卷、炸药筒的信息。
10.
A close-fitting knitted pullover shirt, jacket, or sweater.
紧身针织套衫、夹克衫或内衣
11.
The diaphragm was clamped between two support housings.
隔膜被夹紧在两个支承套之间。
12.
Smaller taper angle of collet, larger clamping power.
弹性套锥形角更小，故夹紧力更大。
13.
Blanket cylinder: In an offset printing press, the cylinder around which the blanket is clamped.
胶布圆筒: 柯式印刷机上被胶布环绕而夹紧的圆筒。
14.
Align the bushing with the spring eye or shackle eye and tighten the nut at the socket wrench end of the threaded roTighten until the bushing is forced into the spring eye.
将衬套对准弹簧眼或U型钩眼，并在螺纹杆的套筒板手末端锁紧螺帽。锁紧直到衬套进入簧眼。
15.
Numerical Simulation and Structural Optimization of Jacketed Tapered Flow Distributor in New Type Heat Exchanger with Longitudinal Flow of Shellside Fluid;
新型纵流壳程换热器夹套式变截面导流筒数值模拟与结构优化
16.
Clinical study on splint by conical telescopic removable denture in severe periodontitis
套筒冠式牙周夹板固定在重度牙周病治疗中的应用观察
17.
They had made shirts, shorts, pantaloons, socks, mittens, sweaters, jackets and scarves.
他们做了衬衫、短裤、松紧裤、袜子、连指手套、毛衣、夹克和围巾。
18.
Tighten needle bar connection screw 2 in needle bar connection 3 so that the marker line of the needle bar aligns with the bottom end of needle bar lower bushing 1 at the lowest position of the needle bar.
在针杆最下点，让针杆下金属部件1对准针杆的刻线，然后拧紧针杆套筒3紧固螺丝2。