1.
Visual detection of welding groove gap with linear laser source
采用激光线光源的焊接坡口间隙视觉检测
2.
Research on Welding Gradient Optimization Process of 80kg Heavy Gauge Steel Plate in Hydraulic Support
液压支架用80kg级高强钢焊接坡口角度优化研究
3.
Above-mentioned transducer can directly track the beveled sides, the edge of weld groove as well as the artificial tracking line (plastic tape).
传感器可直接跟踪焊接坡口的斜面或棱边,也可以跟踪人为跟踪线(塑料带).
4.
A study of the improvement of the butt weld groove of a boiler set box and pipe
锅炉集箱和管道对接焊坡口的改进研究
5.
Research on real-time processing images of non-groove butt weld based on structured light
基于结构光无坡口对接焊缝图像实时处理研究
6.
One side welding thermal cycle measuring experiment of heavy plate with V-shape groove
特厚钢板V型坡口单面焊接热循环测定实验
7.
For all processes, the Welding Procedure Specification (WPS) shall contain a detailed cleaning procedure indicating joint preparation prior to welding.
对于所有焊接方法，焊接工艺规程都应详细包含清除方法，说明焊前坡口的准备。
8.
The old method of soldering metal sheets together has now been largely replaced by welted joints, which are made by a special efficient mechanical device.
搭接贴角焊接金属薄板的老方法,现今已基本上为对接坡口焊所取代。
9.
These attachments were considered secondary components, so no weld quality control has been imposed on the groove weld splice.
这些附连件被看作是次要的部件，所以在这种坡口焊接中没有进行焊接质量控制。
10.
Subcontractor is responsible for trimming the random ends to the correct size (dimensions) final fit-up, end preparation and welding.
“分包商负责将管端切削至合适的尺寸、坡口加工和组对焊接。”
11.
Indicates a weld in a flared-bevel groove. Stems will elongate when height is increased.
指示在喇叭形坡口焊接。杆可随着高度的增加而拉长。
12.
Cracks have been found in the flange and web splices at groove welds in at least four bridges.
至少在四座桥梁的翼缘板和腹板拼接坡口焊缝中发现了裂纹。
13.
The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection.
第二种是产生于立柱翼缘与主梁翼缘连接处的坡口焊缝焊趾处的裂纹。
14.
Study on Groove Shape and the Open Angle of End Tab of UOE Pipe;
UOE焊管坡口形状与引弧板开口角研究
15.
tinning the ends of the wires makes a better joint when you solder them.
当你焊接接口时，用锡焊很管用。
16.
A large number of these cracks occurred because the groove welded component was considered a secondary member or attachment.
发生这许多裂纹是因为把这些坡口焊接部件作为次要构件或附件考虑。
17.
Effect of Outside Welding Groove Angle on Weld Quality of X80 Grade SSAW Pipe
外焊坡口角度对X80级螺旋埋弧焊管焊缝质量的影响
18.
TFE disc valves limite to450 oF temperatures.
焊接连接端口阀门温度限制在不影响焊接连接端口的强度范围内。