1.
Research on Rolling Process for Strengthen Car's Crankshaft and Design on Rolling Mechanism;
轿车曲轴圆角滚压强化工艺研究与滚压机构设计
2.
Research on Variable Force Crankshaft Rolling and Deformation Rule;
曲轴变力圆角滚压强化及变形的规律研究
3.
The Deformation Analyses and Expert System Researches on Crankshaft Rolling-aligning;
曲轴圆角滚压变形分析及校直专家系统的研究
4.
The Research of the Deformation in the Rolling Process for Strengthen Crankshaft;
曲轴圆角滚压强化工艺中曲轴变形的研究
5.
Fatigue Strength and Fillet Rolling Study of Ductile Iron Crankshaft for YC6108ZQ Diesel Engine
YC6108ZQ柴油机球铁曲轴疲劳强度及圆角滚压研究
6.
The Nitrogen Turns+The Circle Cape Rolls To Press The Compound Enhances The Axial Application Study In Spheroidal Graphite Cast Iiron Crankshaft
氮化+圆角滚压复合强化球墨铸铁曲轴的应用研究
7.
The Design of the Numerical Control System for Cranshaft Chamfer Rolling and the Imitation of Movement Base on the Software-Solidworks;
曲轴圆角滚压数控系统研究及基于Solidworks的运动仿真
8.
Research on Crankshaft Rolling Alignment Based on Artificial Intelligent Expert System;
人工智能专家系统在曲轴圆角滚压校直中的研究
9.
Use of Neural Network Internal Model Control in Automotive Crankshaft Fillet Rolling System
神经网络内模控制在汽车曲轴圆角滚压系统中的应用
10.
The limit bending capacity of a round-corner-rolled crankshaft is measured with the testing machine.
利用该试验机对日本大发公司生产的经过圆角滚压处理的曲轴的极限承载弯矩进行了测试。
11.
Fluctuation of Pressure Analysis and Research on Mouth of the Tongs of Crankshaft;
汽车曲轴圆角冷滚压钳口压力波动分析及研究
12.
roller for self-opening thread rolling head
滚压式板牙头用圆滚子
13.
The analytic method of pressure angle of the conical cam mechanism with oscillating conical roller follower
圆锥滚子摆动从动件圆锥凸轮机构压力角的解析方法
14.
Calculation of Pressure Angle and Minimun Average Cylinder Radius of Cylindrical Cam Mechanisms with Oscillating Roller Follower by Using Instantaneous-center Method
用瞬心法求滚子摆动从动件圆柱凸轮机构压力角和最小平均圆柱半径
15.
Design of Fillet Parameter of Needle-cage Assembly
滚针轴承保持架组件圆角参数的设计
16.
Combined Standard Appliance With Arc Formation Angle Block Used to Check Taper Raceway
检验圆锥滚道用弧形角度块组合标准器
17.
Suitable Design of Tooth Profile Angle of Transition Edge for Round-head Gear Hob for Pregrinding Hobbing
圆头留磨滚刀过渡刃齿形角的合理设计
18.
cylinder for calendering or rolling machines (excl. metal- or glass-working machines)
砑光机或滚压机（金属或玻璃加工机除外）圆筒