1.
Precise preform loading system in order to minimize failure rate.
高可靠性的进坯、上坯、出坯系统、使吹瓶机故障率降到最低。
2.
This paper proposed consult ideas about how to increase the pehtze production rate and improve the protein utilization ratio of raw materials.
就如何提高原料蛋白质利用率及白坯出坯率提出了参考意见。
3.
strong winds; a hard left to the chin; a knockout punch; a severe blow.
强风；很难把下巴转到左边；出坯杆；剧烈的喘气。
4.
Minimum Mould Exit Shell Thickness of Round Blooms for Peritectic Steel Casting
包晶钢圆坯结晶器出口安全坯壳厚度的研究
5.
In the injection stretch blow moulding process, injection moulding machine is used to make the preform.
注拉吹工艺先用注塑机注出瓶坯。
6.
The sculptor roughed out the form his statue should take.
雕刻师制出了雕像的毛坯。
7.
STUDY ON PARISON SWELL OF MODIFIED PVA IN EXTRUSION BLOW MOLDING
改性聚乙烯醇挤出吹塑型坯膨胀研究
8.
Temperature Estimation of a Heated Armor Plate′s Original Surface Based on Deferred Infrared Temperature-measuring
红外仪延迟测量法确定板坯出炉温度
9.
This machine applies to cutting the adobe strips extruded from plasticity or half-plasticity and use with single and double jaw brick-make machine.
本机适用于切割硬塑或半硬塑挤出的坯条，与单、双泥条挤出切坯配套使用。
10.
Analysis of the Temperature of Slabs out of CCM in HCR Technology
热送热装工艺中板坯出连铸机温度的分折
11.
Effect of slab strain on Nb(C,N) precipitation in continuous casting process
连铸过程铸坯应变对碳氮化铌析出行为的影响
12.
Study on microstructure and precipitated phases in Al0.3Mn0.4Fe twin-roll casting Al-strip
Al_(0.3)Mn_(0.4)Fe合金铸轧板坯晶粒和析出相分析
13.
Study on Design and Optimization Techniques of Parison Thickness for Extrusion Blow Molding
中空挤出吹塑型坯壁厚设计与优化技术研究
14.
Therefore the deformation, strain, stress and the force of the roller on the slab are obtained for each stage of the casting.
由此得出了铸坯在各个阶段的变形、力及辊子对铸坯的夹持力、直力矩等。
15.
The sizes of slabs, the casting speeds of CCM and the cooling methods in second cooling zone are key factors which affecting the temperature of slabs out of CCM.
影响铸坯出连铸机温度的主要因素是铸坯尺寸、连铸机拉迪和冷却制度。
16.
Speaking the truth, it is the touchstone of potters' skills in throwing.
从在哪个部位分段，可以看出拉坯师傅的技艺好坏和水平高低。
17.
The inclusions distribution in ingot was examined by means of microscopy.
通过对解剖钢坯的金相检验,找出了夹杂物在钢锭中的分布规律。
18.
Turning operations are required to make many different cylindrical shapes, such as axes, gear Blanks, pulleys, and threaded shafts.
车削用来切削出不同的圆柱形,如转轴、齿轮毛坯、滑轮、螺纹轴等。