1.
Study on Internal Force Redistribution and Moment Modification in Prestressed Concrete Frame;
预应力混凝土框架塑性内力重分布与弯矩调幅的研究
2.
Effects of Dynamic Crane Load on the Redistribution of Moment and Deformation of Steel Gabled Portal Rigid Frames
吊车动荷载对山形门式钢刚架塑性内力重分布和变形的影响
3.
Experiment Study on Moment Redistribution in Continuous Haycite Concrete Beams;
陶粒钢筋混凝土连续梁塑性内力重分布的试验研究
4.
ELASTIC-PLASTIC ANALYTICAL SOLUTION OF DEEP BURIED CIRCLE TUNNEL CONSIDERING STRESS REDISTRIBUTION
考虑应力重分布的深埋圆形透水隧洞弹塑性解
5.
Effect of in-crack water pressure distribution on the fracture behavior of concrete gravity dams
裂纹内水压分布对重力坝断裂特性的影响
6.
Elastic-plastic deformation effect on distribution of stress and axial force in a threaded bolt
弹塑性变形对螺栓应力和轴力分布的影响
7.
Internal Forces Redistribution and Stresses Redistribution Analysis of Continuous and Prestressed Concrete Girder Bridges
预应力混凝土连续组合梁桥的内力重分布与应力重分布分析
8.
Analysis of the Bearing Capacity and Stress Re-distribution of the D-Steel-Concrete Composite Beam;
双层连续组合梁承载力及内力重分布的研究
9.
INTERNAL FORCE REDISTRIBUTION AND CRACK CONTROL OF PRESTRESSED CONCRETE FLAT-FLOORS
预应力平板结构的内力重分布和裂缝控制
10.
Numerical simulation of the residence time distribution in a continuous stirred tank with a pseudoplastic fluid
连续搅拌槽内假塑性流体停留时间分布的数值模拟
11.
Study on Secondary Internal Force and Redistribution of Internal Force about Two-span Prestressed Concrete Frame;
两跨预应力混凝土框架次内力及内力重分布规律研究
12.
Study on Elastic-Plastic Stress and Bearing Capacity of Longtan RCC Gravity Dam;
龙滩碾压混凝土重力坝弹塑性应力和承载能力分析研究
13.
The Analysis of "Plastic Instability" Phenomenon of the Equal-thickness Spherical Shell under Uniform Intrinsic Pressure;
均布内压等厚球壳局部塑性失稳研究
14.
Effect of Triaxial Stress on the Plastic Zone Distribution in Front of Crack Tip with Mixed Mode Loading
三轴应力状态下复合型裂纹尖端前缘的塑性区分布
15.
Some New Analytical Results for Plastic Buckling and Initial Post-Buckling of Plates and Cylinders Under Uniform Compression
均布压力作用下板和柱面塑性屈曲和初始后屈曲的分析结果
16.
Research on the Structural Force Redistriution for Double-Curved Arch Bridges Reforming;
双曲拱桥拓宽改造后内力重分布的探讨
17.
The plastics engineers were in a constant effort to improve the distributive and dispersive mixing performance of the single screw extruder for many years.
为改善单螺杆挤出机的分散和分布混合能力,国内外塑料工程师们多年来进行了不断的努力。
18.
The Relationship between Offset and the Hip Stress in the Total Hip Arthroplasty by the Three-dimensional Photoelastic;
人工髋关节置换术中偏心距重建与聚乙烯内衬应力分布的三维光弹性研究