1.
A Study on Wearing Mechanism of Centrifugal Slurry Pump and Finite Element Analysis;
离心式渣浆泵磨损机理及有限元仿真分析
2.
Abrasion resistant radial wear ring is standard on Model 6123 and smaller. Hardened SS Wear Rings optional on all models.
耐磨的径向磨损环。配置在6123型号和更小的泵上。
3.
EXPERIMENTAL STUDY OF ABRASIVE-CORROSIVE WEAR OF MUD PUMP LINER
钻井泵缸套材料磨料—腐蚀磨损实验研究
4.
Research on the Contamination Sensitivity of Cylinder Bore and Piston Pair in Hydraulic Piston Pump;
海水泵缸孔柱塞副污染磨损机理研究
5.
Measures taken to prevent abrasion of the plunger in cylinder sleeve of a cryopump and to improve sealing performance
低温泵缸套柱塞防磨损和提高密封性的措施
6.
Research on the Contamination Wear and Its Control of Slipper Pairs in Hydraulic Piston Pumps;
海水泵滑靴副污染磨损及控制方法研究
7.
Pilot Study about the Contamination-wearing Mechanism of Seawater Hydraulic Pumps and Its Experimentation;
海水液压泵污染磨损机理及其实验的初步研究
8.
The Wear Mechanism of Concrete Pumping Pipe under the Conditions of Multiphase Fluid
多相流体条件下混凝土泵送弯管磨损机理分析
9.
Numerical simulation of solid-Liquid two-phase flow and abrasion characteristics in desulfurization pump
脱硫泵固液两相流动的数值模拟与磨损特性
10.
Study on 3-D Turbulence Numerical Simulation and Wear Characteristics of Slurry Pump
渣浆泵三维湍流数值模拟及磨损特性研究
11.
Worn pump bushing and/or failed torque converter – both should be replaced during a rebuild with code 38 present
在重设代码３８时，必须更换磨损的泵轴套和／或破损的扭力转换器。
12.
Investication of Main Factors and Law for the Effects of Wet-Part Materials of Solids-Handling Pumps on Abrasion Wear
影响杂质泵过流件材料磨损的主要因素及其规律的探讨
13.
Numerical Simulation of the Sandy Ablation of Centrifugal Pump Impeller Flowed Passage Parts in High Sandy Flow;
含沙水流中离心式水泵过流部件泥沙磨损的数值模拟
14.
Experimental Research on Plunger Matching Parts of Injection Pump Worn by DME-Diesel Blends;
二甲醚一柴油混合燃料对高压油泵柱塞偶件磨损的实验研究
15.
Experimental Study on Hydraulic Performance and Wear of Double-channel Pump Delivering Solid-liquid Media
双流道泵输送固液介质的水力性能及磨损试验研究
16.
Numerical Calculation of Interior Liquid-solid Two-phase Flow inside a Slurry Pump and Analysis of Wear Character for the Impeller
渣浆泵内固液两相流动的数值计算与磨损特性分析
17.
If oil pressure was low and pump is within specifications, inspect for worn engine bearings or other reasons for oil pressure loss.
如果油压低并且泵在规格表内，则针对油压低的问题检查磨损的引擎轴或其它原因。
18.
Contrast Experiment Research on Plunger Matching Parts Assembly of High Pressure Oil Pump Worn by Diesel Fuel and DME-Diesel Blended Fuel;
柴油、二甲醚—柴油混合燃料对高压油泵柱塞偶件磨损的对比试验研究