1.
ANALYSIS OF ENGAGING GEARS WITH DOUBLECIRCULAR-ARC TOOTH PROFILESⅡ. CORRECTLY ENGAGING CONDITIONS AND PRIMARY RESEARCH OF INTERFERENCE
双圆弧齿轮传动的啮合分析 Ⅱ.正确啮合条件及齿形干涉浅析
2.
The Judgment Condition for the Involute Gear Pair with Fewer Teeth Number outside Pitch Point;
少齿数渐开线齿轮节点外啮合的判定条件
3.
A transmission analysis for standard straight gear based on accurate modeling
精确建模条件下标准直齿轮啮合传动分析
4.
Transmission Analysis of an Arc Teeth Synchronous Belt Considering the Complex Contact Conditions
复杂接触条件下圆弧齿同步带啮合传动分析
5.
Continuity Condition of Profiles for Internal-Meshing Cycloid Rotary Compressor
内啮合摆线转子压缩机型线连续性条件研究
6.
Study on Meshing Analysis and Meshing Control of Double-enveloping Hourglass Worm-gearing Affected by Misalignment Errors and Load-dependent Deformation
制造误差与承载变形耦合条件下平面二次包络环面蜗杆的啮合分析与啮合控制研究
7.
The formulas of essential and sufficient conditions for actual double pair tooth engagement, as well as the formula of actual contact ratio, are also proposed.
提出了实际双齿啮合必要和充分条件及实际重合度的概念及公式。
8.
A small cogwheel that engages or is engaged by a larger cogwheel or a rack.
小齿轮，齿杆啮合大齿轮或被大齿轮或齿条啮合的小齿轮
9.
Theoretical and Experimental Study of NI-MPE in Intermeshing Co-Rotating Twin-Screw Extrusion;
啮合同向双螺杆挤出过程非啮合多过程元件的理论及实验研究
10.
[U]action or result of engaging(parts of a machine,etc)
（机器零件等）啮合的动作或结果
11.
Meshing Calculation Formulas of Spatial Cam Mechanisms with Concentric Roller Followers
空间同心滚子从动件凸轮机构的啮合计算公式
12.
Simulation of Flight Element Runner in Co-Rotating Twin Screw Extruder;
啮合同向双螺杆挤出机螺纹元件流场分析
13.
This paper makes a meshing analysis about the spiroid gearing. Using the method of equivalent worm gearing, the assembly condition of Archimedes spiroid gears has been obtained.
通过锥蜗杆传动副的啮合分析,用当量圆柱蜗杆副的分析方法,得出阿基米德锥蜗杆副的装配条件。
14.
To join or attach by means of a joggle.
榫接，啮合用啮合扣或接榫连接或安装
15.
A Periodically Time-varying Mesh Stiffness Model for Spur Geared System Considering the Effect of Extended Tooth Contact
考虑延长啮合时齿轮副啮合刚度模型
16.
Study on Properties of Mixing Elements in Melt Conveying Zone of Intermeshing Counter-Rotating Twin Screw Extruder;
啮合异向双螺杆挤出机熔体输送段混合元件性能的研究
17.
Study on a New Mixing Element and Screw Configuration in Intermeshing Co-Rotating Twin Screw Extruder;
啮合同向双螺杆挤出机新型混合元件及螺杆构型的研究
18.
Insert front cable through the parking brake lever basInsure the cable retainer is seated into the base.
将前钢缆穿过手刹车拉杆底座。钢缆扣件务必啮合到底座。