1.
The ortho cone helicoid was used interrsect intercept by the ortho cone helicoid and the cylinder.
正圆锥螺旋面是正圆柱螺旋面被同轴正圆锥面截得。
2.
Introduction to the Technique of Eccentric Helicoid Substituting Archimedean Skewedly Relieved Spiral Surface
用偏心圆锥曲面代替阿基米德斜铲螺旋面工艺简介
3.
The mathematical principle of the generation of cone roller′s centerless super roller guide spiral camber;
圆锥滚子无心超精导辊螺旋曲面生成的数学原理
4.
Vibration-prevention Lathing Process for Long Shaft Circumference of Tapered Spiral Blades
锥形螺旋叶片长轴外圆防振车削工艺
5.
A three-dimensional curve that lies on a cylinder or cone, so that its angle to a plane perpendicular to the axis is constant.
螺旋线附着于圆柱体或圆锥体之上的三维曲线，其垂直于中轴线的平面角是一个恒量
6.
Measurement and Error Analysis for Loxodrome Normal Circular-arc Spiral Bevel Gear;
斜航式法向圆弧螺旋锥齿轮的误差测量分析
7.
Finite Element Stress Analysis for Loxodrome Normal Circular-arc Spiral Bevel Gear;
斜航式法向圆弧螺旋锥齿轮强度的有限元分析
8.
Research on the Airborne Conical Log-Spiral Antennas with Two Types of Excitation
机载圆锥对数螺旋天线及两种馈电方式的研究
9.
Development of Conical Spiral Groove Aerodynamic Bearings Experimental System
圆锥螺旋槽气体动压轴承实验台装置研制
10.
Computer-aided design of conoid helical-coil compression spring with equal pitch
等节距圆锥螺旋压缩弹簧计算机辅助设计
11.
3D Modeling and Optimization Analysis of Blades and Taper-spiral Auger’s Tip
刀片及圆锥螺旋钻尖的三维建模和优化分析
12.
The Design and Experiment of the Screw Cone Flanges Built-up Maize Pick Roller
螺旋圆锥凸棱式玉米收获摘穗辊的设计与试验
13.
Difference Surface Model Establishment and Simulation in Spiral Bevel Gear
螺旋锥齿轮差曲面模型的建立与仿真
14.
Study on Principle of Bertrand Conjugating Surfaces and Loxodrome Normal Circular-arc Spiral Bevel Gear Transmission
白川德共轭曲面的基本原理与斜航式法向圆弧螺旋锥齿轮传动的研究
15.
the constant angle at which a helix cuts the elements of a cylinder or cone.
一个螺旋状物切割圆柱体或圆锥体的某些部分而形成的连续的角。
16.
a brass musical instrument consisting of a conical tube that is coiled into a spiral and played by means of valves.
通过筏吹奏由盘旋成螺旋形的圆锥管组成的铜乐器。
17.
The Research on Evaluation Method of Tooth Surface Topographic Deviation for Spiral Bevel Gear;
螺旋锥齿轮齿面拓扑误差评定方法的研究
18.
Research on Surface Roughness for Multi-axis NC Grinding of Spiral Bevel Gear
多轴数控磨削螺旋锥齿轮的表面粗糙度研究