1.
The Research of the Deformation in the Rolling Process for Strengthen Crankshaft;
曲轴圆角滚压强化工艺中曲轴变形的研究
2.
An qualitative analysis and some solutions of diesel s crankshaft deformation;
柴油机曲轴变形的定性分析及解决措施
3.
Elastohydrodynamic Lubrication Analysis of Crankshaft Bearing Considering Crankshaft Deformation under Load and Roughness Surface;
计入曲轴受载变形的粗糙表面曲轴轴承弹性流体动力润滑分析
4.
Thermohydrodynamic Lubrication Analysis of Crankshaft Bearing Considering Crankshaft Deformation under Load;
计及曲轴受载变形的曲轴轴承热弹性流体动力润滑分析
5.
Elastohydrodynamic Lubrication Analysis of Crankshaft Bearing Considering Crankshaft Deformation and Block Distortion
计及曲轴和机体变形的曲轴轴承弹性流体动力润滑分析
6.
Axial load-deformation curve and preload on angular con act ball bearings
角接触球轴承的轴向载荷—变形曲线和预紧
7.
Calculation of Dynamic Stress and Fatigue Strength of Crankshaft with Bush Deformation Included
计入轴瓦变形的曲轴动应力和疲劳强度计算
8.
The influence of the journal misalignment in bearing bore resulted from crankshaft deformation when it acted by load should be considered in the lubrication analysis of crankshaft bearing.
曲轴轴承的润滑分析应该考虑曲轴受载变形导致轴颈在轴承孔中倾斜的影响；
9.
Research on Variable Force Crankshaft Rolling and Deformation Rule;
曲轴变力圆角滚压强化及变形的规律研究
10.
Check the deflection of the crankshaft both before and after repair.
在修理前和修理后都要检查曲轴的变形情况。
11.
Experimental Research for Complete Stress-Deformation Curve of Concrete in Unixial Tension;
混凝土单轴拉伸应力～变形全曲线试验研究
12.
Study of Critical Theory about Buckling Forming of Middle Thick-walled Tube Bearing Axial Load;
中厚壁圆管轴压屈曲极限变形理论研究
13.
The Deformation Analyses and Expert System Researches on Crankshaft Rolling-aligning;
曲轴圆角滚压变形分析及校直专家系统的研究
14.
Study on Hot Deformation Behavior of Medium-Carbon Non-quenched and Tempered Steel for Crankshafts
一种曲轴用中碳非调质钢的热变形行为
15.
Buckling of compressed bar subjected to combined effect of axial loads considering shear deformation
考虑剪切变形时轴向载荷联合作用下压杆屈曲
16.
Experimental and Theoretical Study on Distortional Buckling of Cold-Formed Thin Wall Steel Lipped Channel Columns under Compression;
卷边槽形冷弯薄壁型钢轴压柱畸变屈曲的试验和理论研究
17.
Research on the Experiment Device for the Complete Stress-deformation Curve for Concrete in Axial Tension;
混凝土轴向拉伸应力—变形全曲线试验装置的研究
18.
The Crankshaft Parametrical Model Technique and Intensity and Study of Residual Deforming in Rolling;
曲轴参数化建模技术及强度和滚压残余变形的研究