1.
Slot-Based Continuous-Time Formulations for Scheduling Multiple Parallel Machines
基于时间槽的并行机调度连续时间建模方法
2.
Time is adjustable, every trough stays for 1.5 minutes when maximum speed.
时间可调，最快时每槽停留1.5分钟。
3.
There's still time to drain the reservoir before the dam breaks.
在水库崩溃之前还有时间排干贮水槽.
4.
She stacked the dishes in the sink because she did not have time to wash them.
她把碗碟堆在洗涤槽里，因为她当时没时间洗。
5.
Time series analysis on differential pressure signals of gas-liquid two-phase flow through slotted orifice
槽式孔板气液二相流差压信号的时间序列分析
6.
Effects of varying creep feeding duration on proportion of pigs consuming creep feed and pre-weaning performance
仔猪教槽(一):不同教槽持续时间对窝采食仔猪比例及仔猪断奶前生长性能的影响
7.
Tank size, supports, acid concentrations, charging schedule, plate alignment, etc. are the same as described.
槽的尺寸，支架，酸的浓度，充电时间，极板的排列等与所描述的一样。
8.
After the placement of an implant, the osseointegration process may last anywhere from two to six months.
植体置入后，与骨槽的融合时间需两个月至六个月。
9.
Numerical simulation of the residence time distribution in a continuous stirred tank with a pseudoplastic fluid
连续搅拌槽内假塑性流体停留时间分布的数值模拟
10.
Effects of etching or no etching on the failure rates of second bonded metallic brackets
酸蚀与未酸蚀对不同时间金属托槽再次粘接后脱落率的影响
11.
Ductor roller: On an printing press,the roller which alternately contacts the duct roller and distributing roller.Length of contact or "dwell" of ductor can be adjusted.ALso called Feed roller.
输送轴:印刷机上，分别接触墨槽和分布轴的一支轴。接触时间或停顿时间是可以调校的。
12.
Slot failed to Initialize.
在初始化插槽时失败。
13.
pronounce with a flap, of alveolar sounds.
发齿槽音时用节拍发出。
14.
the dwell of the feed roller with the duct roller;the dwell of the blocking surface with the printing substrate.The speed of machine affects the dwell.
例如输送墨轴和墨槽轴的接触时间;烫印印版和被印物品的接触时间等。机器的速度影响停顿时间。
15.
Any of the spaces between two triglyphs on a Doric frieze.
三槽板间平面陶立克柱式雕带上两个三联浅槽间的空间
16.
With centrifugal model test study of covered excavation construction of Shenzhen Subway, anthors got the change rule curve of ground surface sedimentation slots which change along with variation of time.
通过对深圳地铁暗挖施工的离心模型试验研究,得到了随时间变化的地表沉降槽变化规律曲线。
17.
On Feb. 5(superscript th) of year 2002, the bid was opened and Kawasaki Heavy Industries Ltd. got the bid.
兴建乙烯冷冻槽，进口乙烯，是在短时间内提高本公司乙烯供应能力最可行的办法。
18.
For some time it has been the practice to install both multitank and single-vessel reaction units outdoors.
有时把多槽和单槽反应装置装设在室外。