1.
Failure of Boiler Blower Fan Resulted from Bush Fixing
紧定衬套安装而导致的快锅风机问题
2.
Xiangshui Red Star Adapter Factory was founded in October2000 with the development of industrial.
响水县红星紧定衬套厂于2000年10月诞生。
3.
A fixed or removable cylindrical metal lining used to constrain, guide, or reduce friction.
衬套，套管一种固定或可移动的圆柱形金属套管，用来压紧、引导或减小摩擦
4.
Install the bushing by tightening the Long Nut.
通过扭紧长螺帽来安装衬套。
5.
Hold puller screw and tighten puller nut until bushing is remove
握紧拉拔器螺栓，拧紧拉拔器螺母，直至拆下衬套。
6.
Align the bushing with the spring eye or shackle eye and tighten the nut at the socket wrench end of the threaded roTighten until the bushing is forced into the spring eye.
将衬套对准弹簧眼或U型钩眼，并在螺纹杆的套筒板手末端锁紧螺帽。锁紧直到衬套进入簧眼。
7.
Tighten leaf spring press until bushing is extracted from leaf spring.
上紧叶片弹簧加压机直到衬套被拔出叶片弹簧。
8.
STUNNING AND UNIQUE? A HOLIDAY MUST-HAVE? OUR LINED STRETCH LACE BUSTIER With floating padded under wired Bra featuring embroidery on top of cups, sequin and ribbon flowerettes, and hook& eye back closure.
佳节必备紧身衣2件一套:胸罩有薄衬和钢圈创造出深型魔法，弹性紧身衣衬托妳的水蛇腰！
9.
He wore prim suits with neckties set primly against the collar buttons of his white shirts.
他穿着整洁的外套，领结紧贴着白色衬衫领口的钮扣。
10.
They had made shirts, shorts, pantaloons, socks, mittens, sweaters, jackets and scarves.
他们做了衬衫、短裤、松紧裤、袜子、连指手套、毛衣、夹克和围巾。
11.
Sintered metal bushes--Determination of radial crushing strength
GB/T6804-1986烧结金属衬套径向压溃强度测定法
12.
Study on one step injection forming machine of screw pump stator lining
螺杆泵定子衬套一步法注射成型机的研究
13.
Improvement of Bearing Bush Fixture in Accessory Gearbox for a Typical Engine
某型发动机附件机匣轴承衬套固定结构的改进
14.
fitting rubber liner for stern tube
尾轴管橡胶衬套嵌套
15.
The rear axle used on front wheel drive applications of this vehicle is mounted to the rear leaf springs using isolator bushings at the axle mounting brackets.
车轴利用轴固定支架的绝缘衬套固定于后叶片弹簧。
16.
Tighten leaf spring press until bushing flange bottoms solidly against leaf spring eye.
上紧叶片弹簧加压机直到衬套凸缘的底部扎实地扺住叶片弹簧的孔眼。
17.
Loosen but do not fully remove the four bolts that attach the stabilizer bar bushing retainers to the rear axle brackets.
松开但不完全拆卸接合稳定杆衬套扣环与后车轴支架的4支螺栓。
18.
Specification for construction and acceptance of wire pipelines with fastening connection steel conduit
套接紧定式钢导管电线管路施工及验收规程