1.
Thick Layer Base Material Spraying Slope Protection Technique Applying in Shaohuai Highway
邵怀高速公路厚层基材喷射植被护坡技术研究
2.
Modification of the Matrix Materials Used by Ink-Jet Printing and Research on Receiving-Ink Layer
数码喷绘耗材用基材的改性与吸墨层的研究
3.
A new thickness gauge making use of neutron scattering method can be used for quick and nondestructive thickness measurements of sprayed concrete.
中子喷射砼测厚仪利用中子散射法能无损、速地测量喷射砼的厚度。
4.
Study on the Dam Foundation Guards Against Infiltrates of the High-pressure Spray Grouting;
水库坝基砂卵石层高压喷射灌浆防渗技术研究
5.
Coating Thickness Distribution of an Arc and its Simulation Based on The New Model of Spray Gun
基于喷炬新模型的圆弧面涂层厚度分布及仿真研究
6.
Research on Multi-layerd Metal Thickness Testing System Based on GMR;
基于GMR的多层金属板材厚度检测系统研究
7.
Construction Method of Thick Laying Substrate Material Vegetation Protection Slope of Zhuyong Highway
诸永高速公路厚层基材植被护坡施工方法
8.
spray/foam-in-place insulation
现场发泡/喷射绝缘材料
9.
X-ray tin coating thickness gauge
x射线锡涂层测厚仪
10.
Thickness Measurement of Thin Film on Polycrystalline Preferred Orientation Material by X-Ray Diffraction
具有择优取向性的基材表面的薄膜厚度的X射线衍射测量修正
11.
1 Drawer fronts are at least 3/4 inch thick with double wall construction, painted prior to assembly and sound deadened.
抽屉面板有3/4英寸厚，两层结构。装配前各面喷涂完毕，抽屉内有消声材料。
12.
Drawer fronts are at least3/4 inch thick with double wall construction, painted prior to assembly and sound deadened.
抽屉面板有3/英寸厚，两层结构。装配前各面喷涂完毕，抽屉内有消声材料。
13.
Analysis and Calculation of the Width and Thickness of Ink-jet Printing Film
喷墨印刷膜层宽度和厚度的分析计算
14.
The results prove that it is an effective method to controll the temperature of the substitute under spraying, and the thermal-shorck resistance is similar to the thin coating.
结果证明,控制喷涂中基体温度,是制备厚涂层的有效方式,其抗热震损伤性能和薄涂层相似。
15.
Study on Damping Behavior of Particulates Reinforced Al Matrix Composites Fabricated by Spray Atomization and Codeposition
喷射共沉积颗粒增强铝基复合材料阻尼特性的研究
16.
A Primary Study of the Spray Suspension Method to Cast Low Chromium Cast Iron-Matrix Tungsten Carbide Porticle-Reinforced Composites
喷射悬浮法铸造低铬铸铁基碳化钨粒子强化复合材料的初步研究
17.
Numerical Simulation on Extrusion Deformation of Spray-deposited 7075/SiC_p Aluminum Matrix Composite;
喷射沉积7075/SiC_p铝基复合材料挤压变形的数值模拟
18.
Effect of Temperature Gradient Cyclic Pressing on Densification of Spray Deposited SiC_p/7090 Aluminum Matrix Composite;
梯温楔压对喷射沉积SiC_p/7090铝基复合材料致密化的影响