1.
Compacted Graphite Iron-A Material Solution for Modern Diesel Engine Cylinder Blocks and Heads
蠕墨铸铁——现代柴油发动机缸体和缸盖的材料
2.
Position the cylinder heads onto head gaskets and cylinder block.
将汽缸盖安置到汽缸盖罩垫和汽缸体上。
3.
"The Block and head can not be machined flat and smooth enough to provide an adequate seal. Thus, gaskets are used."
机器加工并不能使气缸体和气缸盖平整光滑到严丝密缝,这样就要使用气缸垫。
4.
Remove the engine cylinder head from the cylinder block (refer to cylinder head removal in this section).
从汽缸体拆下引擎汽缸盖（请参阅本部分之汽缸盖拆卸）。
5.
Study on Coupled Heat Transfer Simulation of Diesel Engine Cylinder Body-Cylinder Liner-Cylinder Head-Cooling Water
柴油机缸体—缸套—缸盖—冷却水整体耦合传热仿真研究
6.
The metallurgical quality of cylinder block and head of D114 diesel engine was analyzed.
对D114柴油机缸体、缸盖铸件冶金质量进行了分析。
7.
Like the cylinder block, the head is made from either cast iron or aluminum alloy.
像气缸体一样，气缸盖是由铸铁或者铝合金制成。
8.
The cylinder head is attached to the block with high-tensile steel studs.
气缸盖与气缸体用高强度的钢螺栓缚连结。
9.
RESEARCH ON COMPLEX FOUNDRY TECHNIQUE OF HIGH STRENGTH GRAY IRON FOR CYLINDER BODY & ITS CAP
汽缸体、汽缸盖用高强度灰铸铁的综合铸造技术
10.
Design of Blast Cleaning Streamline for Engine Cylinder Lid and Cylinder Body
4JB1发动机缸盖缸体内腔喷丸清理线的设计
11.
Study on Performance of Pre-coated Sand Core Used for Cylinder Block and Cylinder Head
发动机缸体、缸盖用覆膜砂芯性能的研究
12.
Foundry Quality Improvement for Aluminum Alloy Cylinder Block and Head of KV6 Engine
KV6汽车发动机铝合金缸体缸盖铸造质量改善
13.
Analyses on Dispersed Shrinkage Causes of Diesel Engine Multi-Cylinder Head
柴油机多缸连体缸盖缩松缺陷原因浅析
14.
The joint between the block and the head must be gas-tight so that none of the burning mixture can escape.
气缸体和气缸盖之间的连接必须密封以便没有燃烧的混合气体泄漏。
15.
The joint between the cylinder Block and the head must be tight and able to withstand the pressure and heat developed in the combustion chambers.
气缸体与气缸盖之间的接合处必须保持密封,并且能够承受燃烧室产生的高压和高温。
16.
The cooling liquid is water. Antifreeze compounds are added to the water during the winter. The water jacket are cast into the cylinder Blocks and heads.
冷却液是水。冬季在水中须加人防冻剂。水套被铸人气缸体和气缸盖内部。
17.
Install the engine cylinder head, push rods, rocker arms, bridges, pivots and engine cylinder head cover.
安装引擎汽缸盖、推杆、摇臂、桥、枢轴和引擎汽缸盖罩。
18.
Install cylinder head, intake manifold, and exhaust manifold, refer to cylinder head installation in this section.
安装汽缸盖，进气歧管和排气管，请参阅本部分的汽缸盖安装。