1.
Limit Analysis of Pressure Vessels with Pad Reinforcement under In-plane Moment on Nozzles;
接管纵向弯矩作用下带补强圈容器的极限分析
2.
Limit Analysis for Cylindrical Shells with Opening-reinforcement under In-plane Moment
接管纵向弯矩下带补强圈容器结构的极限分析
3.
Effects of Reinforcing Bar Amount on Bending-resistance Bearing Capacity of Single-side Reinforced Rectangular Beam
纵向钢筋配筋量对单筋矩形截面梁截面抗弯承载力的影响
4.
Eular crippling stress
（纵向弯曲）欧拉临界应力
5.
Study on the Coupled Torsional, Axial and Bending Three-Dimensional Vibrations of Internal Combustion Engine Shafting Basing on Exact Dynamic Stiffness Matrix Methods;
基于精确动态刚度矩阵法的内燃机轴系扭转、纵向及弯曲三维耦合振动研究
6.
It is difficult to execute turns with rudder control alone.
单靠操纵方向舵转弯是困难的。
7.
Study on the Longitudinal Anti-bending Capacity of Nanjing Cross-river Shield Tunnel
南京越江盾构隧道纵向抗弯能力研究
8.
Virtual Work Method of Rectangular Two-Way Slab Considering Resistance Moment of Inclined Yield Line
考虑斜向塑性铰线抵抗弯矩的矩形双向板虚功分析法
9.
And I saw the crisscross of twisting turning streets leading to the square.
也看到了纵横交错、弯弯曲曲的街从不同方向通往广
10.
LONGITUDINAL BUCKLE OF ASYMMETRIC CLADED STAINLESS STEEL PLATES FOR HOT ROLLING
非对称不锈钢热轧复合板材的纵向弯曲
11.
Flexural vibration of a compound bar piezoelectric transducer
复合棒压电纵向振动换能器中的弯曲振动
12.
Experimental Study of Inelastic Buckling Strength and Stiffness Requirements for Longitudinally Stiffened Panels
纵向加劲板非弹性抗弯强度和刚度试验研究
13.
Calculation of the Longitudinal Depth Averaged Velocity Distribution of Curved Conduit Flow
弯道水流纵向垂线平均流速分布的计算
14.
The methods for calculation of additional vertical bending moment and confining bending moment of flanges are deducted, and the type and quantity of radial reinforcements are proposed.
为此，导出了竖向附加弯矩和法兰盘约束弯矩的计算方法，提出了径向联系筋的形式及数量。
15.
The Bending、Vibration and Buckling of Rectangular Orthotropic Thin Plates;
正交各向异性矩形薄板的弯曲、振动和屈曲
16.
Fourier analysis of bending of orthogonal anisotropic rectangular thin cantilever plate
正交各向异性矩形悬臂薄板弯曲的傅立叶分析
17.
Seismic Behaviour of Square CFT Beam-Columns Under Biaxial Bending Moment
双向弯矩作用下方钢管混凝土梁柱的抗震性能
18.
The emphasis of the paper is placed on the influence of the secondary moment and the axial prestress on the moment redistribution.
重点讨论了预应力连续梁中次弯矩和轴向预压力对弯矩调幅的影响。