1.
Equivalent factors of multi-axle loads for asphalt surfacing on steel bridge decks
钢桥面铺装多联轴荷载的当量轴数研究
2.
Study on Charge Standard Calculation Method for Toll-by-weight Based on Equivalent Axle Theory and Equivalent Coefficient Theory;
基于当量轴次和当量系数理论的计重收费计算方法研究
3.
Research on Motion Model of Constant h_(eq)Non_circular Crankshaft Grinding
曲轴非圆的恒当量磨削厚度磨削运动模型研究
4.
Spindle feeds and speeds are controlled by selector levers which engage the proper gears in the drill head.
主轴的进能量和转速是通过选速杆使主轴箱中的适当齿轮相啮合而控制的。
5.
When the exterior normal is opposite to the coordinate axis, then the positive stress components are in the opposite directions of the coordinates.
当外向法线和坐标轴相反时，正的胁强分量就是沿着和坐标轴相反的方向的。
6.
The wheelbase must have an adequate length too.
轴距也应该有适当的长度，因为该参量可以影响底盘强度。
7.
Equivalent Linearization Method for Limit Cycle Flutter Analysis of Plate-Type Structure in Axial Flow
轴向流中板状结构极限环颤振分析的当量线性化法
8.
Total Weight (Less Bearing)
总重量(较少轴承)
9.
Angular momentum is an axial vector quantity.
角动量是一种轴矢量。
10.
In rotating, the shaft splashes oil up into the bearings.
当轴旋转的时候就把油溅入轴承。
11.
Measuring diameter of fore and aft stern tube bearing and bushes.
艉轴管前、轴承与衬套直径测量。
12.
Crankshaft Grinding Process on the Quality of Study on the Impact of the Crankshaft
曲轴磨削工艺对曲轴质量影响的研究
13.
It provided also a large quantity of high precision hydrodynamic-hydrostatic and pneumatic spindle units, inductosyn, etc. for machine tools and aerospace industries.
还为机床、航天等行业部门提供相当数量的高精度动静压、气动主轴部件和感应同步器等产品。
14.
The maximum amount of oil is reached when marker dot A is brought to the position just opposite from the needle bar crank 3 by turning the adjust pin in direction C.
从图上所示的位置向C方向转动，当转到与针杆曲轴3的正对面的位置时，油量为最大。
15.
The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.
当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。
16.
When taking propeller shaft joint angle measurements, or checking the phasing, of two piece shafts, consider each shaft separately.
当测量两个传动轴的工作角或检查它们是否定相时，对它们要分别考虑。
17.
This is the only accurate test because if the liner or lock is engaged you can't tell if the blade pivot is precise.
因为当锁定机构压迫刀体时你无法区别是否刀轴精确性，只有这样才能准确测出晃动量。
18.
In usual vector notation a horizontal wind blowing from 270 degrees would be represented by a vector with its origin at the intersection of the two horizontal axes.
在通常的向量符号中，水平风从270°吹来时，应当表示为零点在两个水平轴的交点。