1.
Considering the difference of cantilever plate between the end and the middle of the concrete box bridge, the chief influence factor is studied.
考虑箱梁端部和跨中悬臂板根部的区别，研究了影响变厚度悬臂根部弯矩的主要因素。
2.
Out-of-Plane Bending Moment Analysis of the Plastic Limit for the Welded Piping Tee Containing Bottom Thinning Defects
底部减薄焊制三通的塑性极限面外弯矩分析
3.
Calculation of Closed Bending Moments for Unbonded Partially Prestressed Concrete (PPC) Beams with High Strength Concrete;
无粘结部分预应力高强混凝土梁闭合弯矩计算
4.
Inspection Analysis on Two Kind of Roll Forming Rectangular Pipe Weld
两种辊弯成型的方矩形管焊缝部位的检测分析
5.
The Plastic Limit Analysis of Circular Plates Under Edge Moments and Local Linear Load
在边缘弯矩和局部线性荷载共同作用下圆板的塑性极限分析
6.
Performance of Partial-Depth End-Plates Beam-To-Column Composite Joints of Steel Frames under Hogging Moment;
部分端板连接梁柱组合节点负弯矩作用时的受力性能研究
7.
Experimental investigation of flow field in both straight and positive bowed stator passages with cantilever blades
带根部间隙的直、弯压气机静叶流场的实验
8.
Analysis of the Effect of Coronal Preflaring on Curved Canal Working Length;
根管冠部预处理对弯曲根管工作长度影响的分析
9.
The beams are designed with respect to the bending moment.
梁是按照弯矩设计的。
10.
Each such beam is subjected to the external loads that normally act upon it, together with the two redundant moments at its ends.
每一根这样的梁承受垂直作用于其上的外荷，以及两端的两赘余弯矩。
11.
On the influence of the bending moment waveform disturbance on the pure bending beam flexion
弯矩波形扰动对纯弯梁弯扭屈曲的影响
12.
The Calculatiou of critical load by torsion angle-bending moment matix;
用转角弯矩矩阵确定压杆的临界荷载
13.
Refraction makes a straight stick look bent if it is partly in water.
折射使一根部分浸在水中的直棍子看起来是弯的。
14.
According to the calculation theory of normal section bending bearing capacity, the calculation formula of cracking moment of high-strength concrete beam was derived by the concrete mechanic method.
根据正截面受弯承载力计算理论,运用混凝土力学分析方法,导出高强混凝土梁的开裂弯矩计算式。
15.
The Influence of Cold-Formed Effect to Stress Capacity Performance of Cold-Formed Rectangular Hollow Section Beams;
冷弯效应对冷弯矩形钢管梁受力性能的影响
16.
COMPARATIVE STUDY ON BENDING STRENGTHENING METHOD OF NEGATIVE MOMENT AREA AT BEAM END IN RC FRAME
梁端负弯矩区受弯性能加固方法对比试验研究
17.
Research on the Curves Versus Moment Hysteretic Behavior of Thin-walled Cold-formed Steel Beams
冷弯薄壁型钢梁的弯矩-曲率滞回性能试验研究
18.
Calculation for Cracking Moment of SRC Flexural Member
型钢混凝土受弯构件开裂弯矩的计算初探